Altigen ACC 6.7 Administration Manual Download Page 78 | Manualshive

Page: 78 / 462

background image

Chapter 4: System Configuration

64

MAXCS ACC 6.7 Administration Manual

Figure 24. System Configuration, Audio Peripheral tab

Configuring Music On Hold and Recorded Announcements

Callers will hear the music or recorded announcement configured on this tab

only

if the

user places the caller on hold.

To configure music on hold when using audio equipment

1. Check

Enable Callers on Hold or in Queue to Listen to Music or Recorded

Announcement

.

2. Select the Triton Analog Station board number to which the audio equipment is

attached.

To configure music on hold to play a file

1. Make sure a VoIP board is installed (required for playing a file).
2. Check

Enable Callers on Hold or in Queue to Listen to Music or Recorded

Announcement

.

3. Use the drop-down list to select the logical board ID of the VoIP board.

The system will play the default music-on-hold file when the user places the caller
on hold.

The default music-on-hold file is a .wav file called “MusicOnWaiting.wav”. The file is
located in the C:\PostOffice\phrases\Music folder. You can replace the file with a .wav
file (or an AltiGen PCM file). A .wav file must be in 8 kHz/ 8 bit/ Mono/ u-Law format.
Any optional music-on-hold files included with MAXCS are in that format. You can
convert your own .wav files to this format using Microsoft Windows Sound Recorder.

«
...
76
77
78
79
80
...
»

Summary of Contents for ACC 6.7















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ACC 6.7

Brand: IBM Pages: 88

Brand: Sun Fire Pages: 66

Brand: Flexport Pages: 39

Brand: Muton Pages: 30

APOGEE Ethernet Microserver 2100

Brand: Siemens Pages: 2

Brand: Siemens Pages: 38

Brand: Siemens Pages: 40

RUGGEDCOM RS401

Brand: Siemens Pages: 50

Brand: Siemens Pages: 101

Brand: Siemens Pages: 116

Brand: Siemens Pages: 143

HiPath Xpressions

Brand: Siemens Pages: 278

Advanced Server UNIX V4.0

Brand: Siemens Pages: 365

Brand: BITMAIN Pages: 20

Brand: TAG Pages: 54

CENTRIX SV-2000-X2

Brand: TAG Pages: 82

Brand: Lantronix Pages: 100

Brand: QNAP Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands