Altigen ACC 6.7 Administration Manual Download | Manualshive

Page: 337 / 462

background image

Chapter 25: Enterprise VoIP Network Management

MAXCS ACC 6.7 Administration Manual 323

4. Click

Create domain and join as master

.

5. Enter the IP address of this system. If this system has multiple IP addresses, enter

the one that can communicate with other member servers.

6. Click

OK

and wait for 5 to 60 seconds, depending on the size and configuration of

the system. The display in the Enterprise Location Manager window changes to show
the name of the VoIP domain and this server as Master.

Declaring Additional Servers for the VoIP Domain

Additional servers are added to the VoIP domain in Enterprise Manager, but first you
must “declare” these servers and assign them a member key in MaxAdmin. To do so:

«
...
335
336
337
338
339
...
»

Summary of Contents for ACC 6.7















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ACC 6.7

UltraNEXUS-HD X5

Brand: Leightronix Pages: 5

Sun Fire X2100 M2

Brand: Sun Microsystems Pages: 128

Brand: AIC Pages: 101

Netfinity 3500 Series

Brand: IBM Pages: 152

Brand: Olive Pages: 19

Brand: Magnimage Pages: 42

Brand: National Instruments Pages: 4

Brand: PCI Pages: 87

Brand: IBM Pages: 16

Brand: EVS Pages: 126

Brand: SeeedStudio Pages: 19

Rackable C2005 2U

Brand: Silicon Graphics Pages: 46

Brand: Silicon Graphics Pages: 162

Brand: UNIVIEW Pages: 30

Brand: 360 Systems Pages: 141

Brand: GIGA-BYTE TECHNOLOGY Pages: 96

Brand: GIGA-BYTE TECHNOLOGY Pages: 99

Brand: GIGA-BYTE TECHNOLOGY Pages: 142

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands