Altigen ACC 6.7 Administration Manual Download | Manualshive

Page: 254 / 462

background image

Chapter 18: Mobile Extension Configuration

240

MAXCS ACC 6.7 Administration Manual

When the mobile extension user calls into the system, any mobile trunk port
can answer the call, verify caller ID, and play a dial tone to the mobile
extension user.

Dedicated

—Only analog trunks can be dedicated mobile trunks. When

selected, you need to assign a mobile trunk port to this mobile extension. You
have the option to disable caller ID verification if a mobile trunk port is
dedicated to this mobile extension. The mobile extension user will hear a dial
tone when calling into this specific trunk port. Use the

Browse

button (

…

) to

select the desired mobile trunk.

Figure 115. Mobile Trunks dialog box

•

In the

Phrase

panel, you have three options: You can select either

Press Any

Key To Answer Call

or

Play Phrase After Answered.

And you can select

Play Phrase Before Dial Tone.

You can use the

Apply

button to apply

selections in this panel to other mobile extensions.

Note

: For mobile extensions running MaxMobile Communicator, you should

clear all three check boxes in the Phrase panel.

•

Press Any Key To Answer Call

—when a call is answered by this mobile

extension user, the system will play the following phrase for the mobile
extension user: “To accept this call, please press any digit.” The user must
press any key within 3 seconds to connect the call; otherwise, it will time out
and the call will be treated as an agent/extension RNA and will be routed
according to its workgroup/extension setting.
If there is a network error or a mobile extension trunk is not available, RNA
handling is applied to the caller. Therefore, it is suggested that you don’t
check the

Set RNA Agent Logout

option for the group that contains the

mobile extension as an agent (Workgroup Configuration,

Call Handling

tab).

•

Play Phrase After Answered

—the system will play the given phrase when

the mobile extension user answers the call from the system. The default
phrase (9037) is a special tone to signal the mobile extension user that this
call can be put on hold, parked, transferred, conferenced.

•

Play Phrase Before Dial Tone

—the system will play the default phrase

9037 (a special tone) and then the dial tone when the mobile extension user
calls into the system through a configured DNIS Access Number.

«
...
252
253
254
255
256
...
»

Summary of Contents for ACC 6.7















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ACC 6.7

Brand: Basalte Pages: 2

Brand: ioCorp Pages: 18

Brand: Jatheon Pages: 52

ProLiant ML110 Gen 10

Brand: HPE Pages: 5

Brand: Yawarra Pages: 4

Brand: MO-SYS Pages: 26

ConnectPort LTS 16

Brand: Digi Pages: 169

Brand: Polycom Pages: 11

Brand: Axis Pages: 168

DIGIARRAY DA-4000E

Brand: Digiever Pages: 9

Brand: Advantech Pages: 6

Brand: Supermicro Pages: 82

Brand: AAxeon Pages: 4

Brand: Lantronix Pages: 78

Brand: Seeed Pages: 9

Brand: Vingtor Stentofon Pages: 68

SC835XTQ - R982B

Brand: Supero Pages: 80

SUPER SUPERSERVER 6026TT-BIBQF

Brand: Supero Pages: 104

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands