manualshive.com logo in svg

Altigen ACC 6.7, Administration Manual

The Altigen ACC 6.7 Administration Manual is an essential resource for effectively managing your Altigen ACC 6.7 system. Download this comprehensive manual for free from our website, providing step-by-step instructions and insights into configuration and administration. Empower yourself with the knowledge to optimize your Altigen ACC 6.7 experience.

Share
Download
background image

x    MAXCS ACC 6.7 Administration Manual

At the Secondary Server  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  345

Checking the Status  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  346
Configuring the NICs   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  347
Configuring the VM Server for NAT Support . . . . . . . . . . . . . . . . . . . . . . . .  349
Monitor Status, Configure Addresses for Enterprise and VM Servers . . . . . . .  350
When the Address of the Softswitch Server Changes  . . . . . . . . . . . . . . . . .  351
Manually Switching Over . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  352
Things to Check  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  352
Getting Notified When the System Switches Over   . . . . . . . . . . . . . . . . . . .  353
Maintenance  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  353

Bootup/Shut Down Procedures  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  353
Configure Only on Active System. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  353

Limitations   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  354

 C

HAPTER

 27

System Report Management  . . . . . . . . . . . . . . . . . . . . . . . . . . . . 357

System Summary Report   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  357
IP Cumulative Traffic Statistics   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  358

Resetting Cumulative Statistics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  359

Using SNMP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  359

SNMP Management Console  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  359
Configuring MAXCS for SNMP  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  359
List of Traps Sent  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  361

 C

HAPTER

 28

Microsoft Exchange Integration   . . . . . . . . . . . . . . . . . . . . . . . . . 363

Requirements   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  363
When You Install MAXCS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  364
Exchange Integration Configuration Steps . . . . . . . . . . . . . . . . . . . . . . . . .  365
Additional Steps for Bridged Access and

 

Native VM Integration  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  368
Configuring UM Settings for Each User . . . . . . . . . . . . . . . . . . . . . . . . . .  371

Configuring for Out Calling from UM  . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  373

Configuring in MaxAdmin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  377

When You Create a New Mailbox User   . . . . . . . . . . . . . . . . . . . . . . . . . . .  380
Testing for Synchronization  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  380

Troubleshooting Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  380

Notes  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  382

 C

HAPTER

 29

TAPI Integration  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 383

Installing the TAPI Proxy Server   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  383
Setting Up the Client   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  383

Install the AltiGen TAPI Service Provider on the Client . . . . . . . . . . . . . . .  384
Set Up Phone and Modem Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  384
Set Up Phone Dialer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  386
Testing TAPI Service Provider on the Client System . . . . . . . . . . . . . . . . .  387

Summary of Contents for ACC 6.7















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ACC 6.7

IBM N Series Installation And Configuration Instructions preview
N Series
Brand: IBM Pages: 7
Razberi V8 Core Manual And Getting Started Manual preview
V8
Brand: Razberi Pages: 113
Paradyne FrameSaver SLV 9126 Installation Instructions Manual preview
FrameSaver SLV 9126
Brand: Paradyne Pages: 24
Moxa Technologies ioLogik W5300 Series User Manual preview
ioLogik W5300 Series
Brand: Moxa Technologies Pages: 177
H3C UniServer E3200 G3 User Manual preview
UniServer E3200 G3
Brand: H3C Pages: 401
7starlake ROC286B User Manual preview
ROC286B
Brand: 7starlake Pages: 32
Mobatime DTS 4132.timeserver Mounting And Instruction Manual preview
DTS 4132.timeserver
Brand: Mobatime Pages: 108
Lucent Technologies Definity 8510T User Manual preview
Definity 8510T
Brand: Lucent Technologies Pages: 85
SEH SEH InterCon PS54a-G Hardware Installation Manual preview
SEH InterCon PS54a-G
Brand: SEH Pages: 24
IBM 87401RU Installation And User Manual preview
87401RU
Brand: IBM Pages: 110
Sun Oracle T5120 Getting Started Manual preview
T5120
Brand: Sun Oracle Pages: 6
Boca Systems BocaVision WT120 User Handbook Manual preview
BocaVision WT120
Brand: Boca Systems Pages: 28
QUANTA QSSC-S99K 2U User Manual preview
QSSC-S99K 2U
Brand: QUANTA Pages: 177
Supero SUPERSERVER 5015M-NT User Manual preview
SUPERSERVER 5015M-NT
Brand: Supero Pages: 134
Acrosser Technology AND-APL1E Series User Manual preview
AND-APL1E Series
Brand: Acrosser Technology Pages: 42
Gigabyte G492-ID0 User Manual preview
G492-ID0
Brand: Gigabyte Pages: 108
QNAP TS-409 User Manual preview
TS-409
Brand: QNAP Pages: 203
Octagon TRAX-10 Technical Manual preview
TRAX-10
Brand: Octagon Pages: 17

Brands by name

Popular brands

Load more brands