Altigen ACC 6.7 Administration Manual Download | Manualshive

Page: 127 / 462

background image

Chapter 10: Application Extension Configuration

MAXCS ACC 6.7 Administration Manual 113

•

Operator

—select an operator from the drop-down list.

Important:

If the failover setting for the application extension is set to an extension, and
the extension is RNA or busy, the call will follow the extension's RNA or busy
call handling.

Application Information

Additional information can be described in the

App Information

fields. If desired, enter

the appropriate information in the fields for

Application

Source

,

Spec

Doc

Location

,

Designed by

,

Implemented by

,

Implementation

Date

,

Revision

Number

and

Revision

Date

.

Readying the Application

If a third-party application is connecting to this extension, make sure the application is
properly set to log into the application extension. If the third-party application is logged
in, the status shown in Figure 53 changes to “connected.”

«
...
125
126
127
128
129
...
»

Summary of Contents for ACC 6.7















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ACC 6.7

Brand: TANDBERG Pages: 127

88631SU - System x3850 - 8863

Brand: IBM Pages: 90

Brand: LTS Pages: 5

Brand: Lantech Pages: 49

Brand: NAIM Pages: 18

Brand: B&B Pages: 55

Silex Pricom SX-2000U2

Brand: Silex technology Pages: 1

Brand: IBM Pages: 24

@server xSeries 343

Brand: IBM Pages: 193

Brand: Sun Microsystems Pages: 121

Brand: QNAP Pages: 69

AlphaServer GS60E

Brand: Compaq Pages: 16

AlphaServer DS20E

Brand: Compaq Pages: 16

ProLiant 4500 Servers

Brand: Compaq Pages: 89

AlphaServer GS60E

Brand: Compaq Pages: 180

Brand: BushkaBlue Pages: 30

Brand: Planet Pages: 28

Brand: W&T Pages: 211

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands