Altigen ACC 6.7 Administration Manual Download

Page: 276 / 462

Chapter 21: Line Park Configuration

262

MAXCS ACC 6.7 Administration Manual

Configuring Line Park

To configure line park,

select

PBX > Line Park Configuration

Figure 124. Line Park Configuration window

Setting Up a Line Park Group

1. In the

Line Park Configuration

window, click the

Add

button below the

Groups

list.

2. Enter a name in the

Add Line Park

dialog box, and click

3. Select line ID numbers from the

Non-Member List

and click the

Add

button to add

them to the

Member List

4. To assign extensions to a group, select the group, and then click the

Configuration

button below the Member Extensions panel.

Summary of Contents for ACC 6.7















































































































































































































































































































































































































































































Search results

Summary of Contents for ACC 6.7

Reviews:

Related manuals for ACC 6.7

Brands by name

Popular brands

Altigen ACC 6.7, Administration Manual

Search results

Summary of Contents for ACC 6.7

Reviews:

Related manuals for ACC 6.7

Brands by name

Popular brands