Altigen ACC 6.7 Administration Manual Download | Manualshive

Page: 40 / 462

background image

Chapter 2: System Requirements and Installation

26

MAXCS ACC 6.7 Administration Manual

•

Softswitch (including VM and Enterprise Manager)

—Select this option to install

Softswitch to the server. You need a dongle for the Softswitch server. Softswitch
provides the following functions:

–

Devices Control

•

IP Phone

•

HMCP Media Server

•

IP Gateway

–

Call Control

•

Call Signal Processing (SIP and H.323 tie trunk)

•

PBX Switching, Routing, and Call Handling

–

System Management

•

Configuration and Directory

•

Phrases and Prompts (System, Custom, Personal)

–

Feature Server

•

Voice Mail Server

•

Multi-Site Enterprise Manager

•

Call Center Feature Server

•

CTI Server

•

Exchange Integration Server

•

CDR Server

•

HMCP Media Server

—If you have a small to medium scale system (no more than

about 200 extensions), you can choose to install Softswitch and HMCP Media Server
in the same machine, if you want to. You can also install them in different machines,
especially if you plan to grow your system.
If your system is larger, install HMCP Media Server and Softswitch on different
servers.
The

HMCP Media Server

check box is not available if the operating system is not

Windows 2003/2008. AltiGen supports HMCP Media Server only on servers provided
by AltiGen.

•

Gateway

—Select this option to install gateway service to an AltiGen IP gateway.

The supported gateway platforms are:

–

OFFICE3G server

–

MAX2000iG (gateway-only MAX server with redundant power supply and RAID
hard drive)

Note:

Do not install gateway service to MAX1000 or MAX1000R server.

When installing Gateway service to an OFFICE3G server, remove Triton
Resource and MeetMe Conference boards. Softswitch server will not use these
boards as conference/barge-in resources.

If you select

Gateway

, the next screen requires you to assign an ID to the gateway.

For detailed instructions on installing and upgrading MAXCS, AltiGen Dealers should refer
to the Knowledge Base, available from the AltiGen Dealer Web Site, at https://
dealer.altigen.com.

«
...
38
39
40
41
42
...
»

Summary of Contents for ACC 6.7















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ACC 6.7

Redbooks ServeRAID-MR10k

Brand: IBM Pages: 48

5big - Network NAS Server

Brand: LaCie Pages: 9

Brand: LaCie Pages: 14

SUPERSERVER 6021F

Brand: Supermicro Pages: 116

Vlinx Serial Servers ESP901E

Brand: B&B Electronics Pages: 92

Brand: HPE Pages: 58

Brand: DNP Pages: 93

Brand: ASROCK Rack Pages: 51

Brand: MO-SYS Pages: 26

Brand: NEC Pages: 4

Express5800/T120e

Brand: NEC Pages: 2

Express5800/T120d

Brand: NEC Pages: 2

Express5800/T110j

Brand: NEC Pages: 32

Express5800/T110j-S

Brand: NEC Pages: 32

Express5800/T120g

Brand: NEC Pages: 40

Express5800/T110g-S

Brand: NEC Pages: 35

Express5800/T110h

Brand: NEC Pages: 40

Express5800/T110i

Brand: NEC Pages: 45

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands