Altigen ACC 6.7 Administration Manual Download

Page: 52 / 462

Chapter 3: Getting Around MaxAdministrator

MAXCS ACC 6.7 Administration Manual

•

Waiting Time

—the longest wait time of callers in queue

•

Service Level

— the percentage of calls in queue with queue time less than or equal

to the defined service level threshold

Current Resource Statistics Window

The

Current Resource Statistics

window displays the total VoIP channels, available

channels, and in-use channels.
The window allows administrators to monitor VoIP channel usage and MeetMe
conference resource use.

Figure 8. Current Resource Statistics window

Top part of the window

Contains a summary of codec usage. The first

G711 only codec

section is displaying

30-port G711 VoIP board codec use.

Middle part of the window

Displays the following data:

•

Gateway ID

—the ID of the VoIP channel’s home gateway

•

IP Resource

—the Triton VoIP

logical board ID:internal DSP channel ID

•

Codecs Capability

—the codecs the IP channel can use

•

Active Codec

—the codec currently being used

•

Used By

—the extension, trunk, SIP channel or H.323 channel that is using this

channel

•

Connect To

—the extension, trunk, or channel the channel is connected to

•

Packets Sent/Received

—the number of voice packets sent and received

•

Bytes Sent/Received

—the total size (in bytes) of all voice packets sent and

received

•

Network Packet Loss

—the number of voice packets that have been lost due to

prolonged delays, network congestion, or routing failure

•

JB Packet Loss

—the number of voice packets that have been discarded due to

jitter buffer overflow

•

Total Packet Loss Rate

—the ratio of total number of lost packets versus total

received packets

Summary of Contents for ACC 6.7















































































































































































































































































































































































































































































Search results

Summary of Contents for ACC 6.7

Reviews:

Related manuals for ACC 6.7

Brands by name

Popular brands

Altigen ACC 6.7, Administration Manual

Search results

Summary of Contents for ACC 6.7

Reviews:

Related manuals for ACC 6.7

Brands by name

Popular brands