Altigen ACC 6.7 Administration Manual Download Page 441 | Manualshive

Page: 441 / 462

background image

MAXCS ACC 6.7 Administration Manual 427

A

P P E N D I X

B

Required Service Parameters

This appendix identifies the recommended and supported parameters for T1, PRI, and
E1 service and provides you with the information needed when you make your service
request.

Service Parameters/Request Information for T1

To subscribe to T1 service, certain parameters are required to establish service. The
information provided below identifies the recommended and supported parameters for
T1 service. When ordering T1 service, provide the following service request information:

Equipment Information

•

PBX Manufacturer—AltiGen Communications, Inc.

•

CSU/DSU—ADTRAN T1 ACE (recommended) or other CSU/DSU

Technical Information for T1 with Voice

Signaling Protocol:

•

E&M Wink Start (recommended)

•

E&M Immediate Start

•

Ground Start

•

Loop Start (not recommended)

Trunk Type:

•

DID

•

2-Way DID (recommended)

•

DOD

Framing:

•

Super Frame (SF)/D4

•

Extended Super Frame (ESF) (recommended)

Line Coding:

•

Alternate Mark Inversion (AMI)

•

B8ZS (recommended)

«
...
439
440
441
442
443
...
»

Summary of Contents for ACC 6.7















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ACC 6.7

Brand: Razberi Pages: 113

Brand: Z Microsystems Pages: 17

Brand: Zonet Pages: 33

Brand: Sun Fire Pages: 66

Brand: MSI Pages: 107

Brand: Sun Microsystems Pages: 90

INTUITY AUDIX LX

Brand: Avaya Pages: 68

Brand: Supermicro Pages: 124

SUPERSERVER 6015C-NT

Brand: Supermicro Pages: 110

AcquiLite EMB A7810

Brand: Obvius Pages: 29

AcquiLite A7810-0

Brand: Obvius, LLC Pages: 29

HP ProLiant DL360P Gen8

Brand: Honeywell Pages: 67

Brand: QNAP Pages: 53

Brand: Samsung Pages: 1

Brand: Samsung Pages: 28

Brand: Samsung Pages: 51

SMARTSERVER 370

Brand: Samsung Pages: 72

Brand: Samsung Pages: 94

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands