manualshive.com logo in svg

Altigen ACC 6.7, Administration Manual

The Altigen ACC 6.7 Administration Manual is an essential resource for effectively managing your Altigen ACC 6.7 system. Download this comprehensive manual for free from our website, providing step-by-step instructions and insights into configuration and administration. Empower yourself with the knowledge to optimize your Altigen ACC 6.7 experience.

Share
Download
background image

MAXCS ACC 6.7 Administration Manual  111

C

H A P T E R

10

Application Extension Configuration

The application extension is an extension pilot number that allows an SDK-based add-
on application to log into the system and establish a communication channel to control 
trunk channels and interact with the system core PBX switching and voice processing 
service. 
Typical applications that use an application extension are:

•

IVR

•

Outbound dialer

•

Inbound call routing logic for a special business application

To connect an SDK-based add-on application, you need:

•

An APC license (concurrent session) 

•

A separate application extension to log in to for each application

For more information about SDK, please send e-mail to [email protected].

Application Extension Setup

Note:

Before you begin, make sure a 

Trunk Control APC SDK Session

 license is 

registered and activated for your system. You can find this information in 

Help

 > 

About

, and then click 

License Information

.

To access the Application Extension Configuration window, select 

System >

 

Application Ext Configuration

.

Summary of Contents for ACC 6.7















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ACC 6.7

HMS Networks Anybus Communicator ABC4018 User Manual preview
Anybus Communicator ABC4018
Brand: HMS Networks Pages: 64
IBM System X Series Rack Installation Instructions preview
System X Series
Brand: IBM Pages: 6
Hanwha Vision SPA-S2000 Quick Manual preview
SPA-S2000
Brand: Hanwha Vision Pages: 16
Epson C823781 Software Installation Manual preview
C823781
Brand: Epson Pages: 28
Epson EpsonNet 802.11b Product Support Bulletin preview
EpsonNet 802.11b
Brand: Epson Pages: 30
Epson Stylus C80WN - Ink Jet Printer Hardware preview
Stylus C80WN - Ink Jet Printer
Brand: Epson Pages: 1
Epson C823781 Administrator'S Manual preview
C823781
Brand: Epson Pages: 258
Epson C82378 Administrator'S Manual preview
C82378
Brand: Epson Pages: 280
Fujitsu PRIMEQUEST 3800E System Configuration Manual preview
PRIMEQUEST 3800E
Brand: Fujitsu Pages: 38
Fujitsu PRIMERGY B900 Reference Manual preview
PRIMERGY B900
Brand: Fujitsu Pages: 36
Fujitsu Primergy BX2560 M1 Operating Manual preview
Primergy BX2560 M1
Brand: Fujitsu Pages: 68
Fujitsu PRIMEQUEST 3000 Series Getting Started Manual preview
PRIMEQUEST 3000 Series
Brand: Fujitsu Pages: 44
Fujitsu PRIMERGY User Manual preview
PRIMERGY
Brand: Fujitsu Pages: 56
Fujitsu PRIMEQUEST 2800B3 System Configuration Manual preview
PRIMEQUEST 2800B3
Brand: Fujitsu Pages: 28
Fujitsu PRIMERGY 870 Technical Manual preview
PRIMERGY 870
Brand: Fujitsu Pages: 35
Fujitsu PRIMERGY 10/40GbE Connection Blade 18/8+2 Function Manual preview
PRIMERGY 10/40GbE Connection Blade 18/8+2
Brand: Fujitsu Pages: 71
Fujitsu PRIMERGY 300 Operating Manual preview
PRIMERGY 300
Brand: Fujitsu Pages: 94
Fujitsu PRIMEQUEST 3800E2 System Configuration Manual preview
PRIMEQUEST 3800E2
Brand: Fujitsu Pages: 42

Brands by name

Popular brands

Load more brands