Altigen ACC 6.7 Administration Manual Download | Manualshive

Page: 406 / 462

background image

Chapter 30: Tools and Applications

392

MAXCS ACC 6.7 Administration Manual

•

PMC chip from host and DSP if T1/E1 board

You have the option of testing a single board or testing all boards at the same time.

CT-Bus Test Tool

The CT-Bus Test Tool is a tool that detects one-way connection, cross talk, bad MVIP
cable and static noise problems.
1. Stop AltiGen Switching Services before running this utility.
2. Launch CT-Bus Test Tool from

Start > All Programs > MAX Communication

Server ACC/ACM > Gateway Tools > CT-Bus Test Tool

.

3. Click

Start

to begin the test.

4. At the end of the test, the utility provides pass or fail results.

Backup and Restore Utility

Note:

The configuration backup option is turned on by default.

To back up or restore data, select either

•

From MaxAdmin:

Services > Utilities > System Data Management

, or

•

From the Windows

Start

menu

: All Programs > MAX Communication Server

ACC/ACM > Utilities > ACC/ACM Backup and Restore.

Figure 172. System Data Management window

Note:

The System Data Management window can only be accessed at the primary
MAXCS system; it is

not

available from a remote MaxAdmin client.

«
...
404
405
406
407
408
...
»

Summary of Contents for ACC 6.7















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ACC 6.7

Brand: Patton electronics Pages: 331

Brand: Korenix Pages: 2

SUPERSERVER 8045C-3R

Brand: Supermicro Pages: 118

Brand: IBM Pages: 100

Brand: IBM Pages: 24

SuperServer 5037C-i

Brand: Supermicro Pages: 88

iPlanet Web Server

Brand: Sun Microsystems Pages: 62

SuperServer 7089P-TR4T

Brand: Supermicro Pages: 155

Brand: Arris Pages: 6

Brand: BITMAIN Pages: 15

Brand: Axis Pages: 172

Brand: GeoVision Pages: 73

Brand: AirLive Pages: 89

Brand: ICPDAS Pages: 104

Brand: QUANTA Pages: 138

Brand: Intel Pages: 233

FXT 5000 Series

Brand: Avere Pages: 48

Brand: TROY Group Pages: 60

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands