manualshive.com logo in svg

Altigen ACC 6.7, Administration Manual

The Altigen ACC 6.7 Administration Manual is an essential resource for effectively managing your Altigen ACC 6.7 system. Download this comprehensive manual for free from our website, providing step-by-step instructions and insights into configuration and administration. Empower yourself with the knowledge to optimize your Altigen ACC 6.7 experience.

Share
Download
background image

vi    MAXCS ACC 6.7 Administration Manual

Configuring Calling Restrictions  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  203

Setting Call Restriction Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  203
Setting Other Call Restrictions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  204

Setting Answering Options   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  204

Forwarding All Calls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  205
Do Not Disturb  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  206
Handling Busy Calls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  207
Setting Call Waiting Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  207
Handling Unanswered Calls. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  207

Configuring One Number Access   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  208

One Number Access Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  209
Call Screening . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  210
Setting Caller ID Verification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  210
Specifying Forwarding Numbers  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  210

Setting Up Monitor Lists  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  211

Configuring a Monitor List. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  211

 C

HAPTER

 16

Setting Up IP Extensions  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 213

Setting an IP Extension   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  217

Setting VoIP Codec for IP Extension. . . . . . . . . . . . . . . . . . . . . . . . . . . .  218

 C

HAPTER

 17

AltiGen IP Phone Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . 221

Configuring Auto-Discovery of Server IP Address  . . . . . . . . . . . . . . . . . . . .  228

Setting Up DHCP Option 120. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  228
On the AltiGen IP Phone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  230
Possible scenarios . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  231
Disabling Auto-Discovery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  231
When You Have Two AltiGen Servers in the Same Network. . . . . . . . . . . .  231

 C

HAPTER

 18

Mobile Extension Configuration  . . . . . . . . . . . . . . . . . . . . . . . . . . 233

MobileExtSP Board Overview  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  234
Configuring the MobileExtSP Board   . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  234

Configuring an Extension as a Mobile Extension  . . . . . . . . . . . . . . . . . . .  237
Additional Configuration for MaxMobile Communicator . . . . . . . . . . . . . . .  241

Voice Mail for Mobile Extensions   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  241
Mobile Extension Limitations  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  241

 C

HAPTER

 19

Hunt Group Configuration  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 243

Overview of Huntgroup Configuration Window  . . . . . . . . . . . . . . . . . . . . . .  244
Setting Up Hunt Groups   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  244

Establishing Basic Hunt Group Attributes  . . . . . . . . . . . . . . . . . . . . . . . .  245
Setting Call Restrictions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  246

Establishing Hunt Group Membership  . . . . . . . . . . . . . . . . . . . . . . . . . . . .  246

Summary of Contents for ACC 6.7















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ACC 6.7

IBM 88631SU - System x3850 - 8863 Installation Manual preview
88631SU - System x3850 - 8863
Brand: IBM Pages: 90
Avaya Virtual Services Platform 7000 Series Troubleshooting Manual preview
Virtual Services Platform 7000 Series
Brand: Avaya Pages: 103
i3 International SRX-Pro Server Quick Start Manual preview
SRX-Pro Server
Brand: i3 International Pages: 2
NEC Express5800/320Fa-L User Manual preview
Express5800/320Fa-L
Brand: NEC Pages: 406
IBM 87401RU Installation And User Manual preview
87401RU
Brand: IBM Pages: 110
Velleman VWS2E Manual preview
VWS2E
Brand: Velleman Pages: 17
IBM P 615 series Service Manual preview
P 615 series
Brand: IBM Pages: 491
Raidon ST7610-4S-S2 User Manual preview
ST7610-4S-S2
Brand: Raidon Pages: 20
IBM Netfinity 3500 Series Manual preview
Netfinity 3500 Series
Brand: IBM Pages: 152
W&T Com-Server++ Manual preview
Com-Server++
Brand: W&T Pages: 228
Interface Masters TAHOE 8824 User Manual preview
TAHOE 8824
Brand: Interface Masters Pages: 34
Olive Olive 4 HD Quick Start Manual preview
Olive 4 HD
Brand: Olive Pages: 19
Supero SUPERSERVER 1018D-73MTF User Manual preview
SUPERSERVER 1018D-73MTF
Brand: Supero Pages: 124
Hewlett Packard Enterprise HPE ProLiant DL580 Gen10 User Manual preview
HPE ProLiant DL580 Gen10
Brand: Hewlett Packard Enterprise Pages: 197
IBM xSeries 342 2RX Maintenance Manual preview
xSeries 342 2RX
Brand: IBM Pages: 158
Acrosser Technology AND-APL1E Series User Manual preview
AND-APL1E Series
Brand: Acrosser Technology Pages: 42
Fujitsu PRIMERGY SX940 Manual preview
PRIMERGY SX940
Brand: Fujitsu Pages: 44
Fujitsu PRIMERGY RX900 S2 Operating Manual preview
PRIMERGY RX900 S2
Brand: Fujitsu Pages: 114

Brands by name

Popular brands

Load more brands