Altigen ACC 6.7 Administration Manual Download Page 384

Page: 384 / 462

Chapter 28: Microsoft Exchange Integration

370

MAXCS ACC 6.7 Administration Manual

Figure 159. The name of our example gateway is “LeslieXia” and the name of the dial

plan we created is “LeslieXiaSS”.

a. Enter the name of the gateway.
b. Enter the IP address of your MAXCS server.
c.

Browse for and select the dial plan you just created.

d. Click

New

5. If your system has multiple gateways, repeat step 4 to add all of your gateways as

UM IP Gateways.

6. Associate your dial plan to the Exchange Server UM. To do this, in the Exchange

Management Console, go to

Server Configuration > Unified Messaging

, select

the server and click

Properties

Summary of Contents for ACC 6.7















































































































































































































































































































































































































































































Search results

Summary of Contents for ACC 6.7

Reviews:

Related manuals for ACC 6.7

Brands by name

Popular brands

Altigen ACC 6.7, Administration Manual

Search results

Summary of Contents for ACC 6.7

Reviews:

Related manuals for ACC 6.7

Brands by name

Popular brands