Altigen ACC 6.7 Administration Manual Download | Manualshive

Page: 443 / 462

background image

MAXCS ACC 6.7 Administration Manual 429

Technical Information for PRI with Voice

Switch Type:

•

5ESS (recommended)

•

DMS (recommended)

•

NI-2 (recommended)

•

4ESS

Framing:

•

Super Frame (SF)/D4

•

Extended Super Frame (ESF) (recommended)

Line Coding:

•

Alternate Mark Inversion (AMI)

•

B8ZS (recommended)

Physical Termination:

•

RJ-48X or RJ-48C

Wire:

•

4 wires

PRI Channel Assignment

D Channels Assignment—24th channel (channel ID 23)

Note:

MAXCS ACC/ACM can configure any channel in a PRI span to be the D channel.
The default setting is the last channel. Every span should select a D channel
within the span. Shared D channel (NFAS) or back up D channel is not
supported.

Hunting—Most Idle, Least Idle, Ascend, Descend
DNIS Digits—can be 3 to 10 digits

CSU/DSU Requirements

The CSU (channel service unit) is a device used to connect a digital trunk line coming in
from the phone company to the PBX. A CSU can terminate signals, repeat signals, and
respond to loopback commands sent from the central office.

Service Parameters/Request Information for E1

To subscribe to E1 service, certain parameters are required to establish service. The
information provided below identifies the recommended and supported parameters for
E1 service. When ordering E1 service, provide the following service request information:

Equipment Information

•

PBX Manufacturer—AltiGen Communications, Inc.

•

CSU/DSU—ADTRAN T1 ACE (recommended) or other CSU/DSU

«
...
441
442
443
444
445
...
»

Summary of Contents for ACC 6.7















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ACC 6.7

BladeCenter QS20

Brand: IBM Pages: 92

BladeCenter JS20

Brand: IBM Pages: 218

HS21 - BladeCenter - 8853

Brand: IBM Pages: 80

8835 - Eserver 325 - 1 GB RAM

Brand: IBM Pages: 62

8835 - Eserver 325 - 1 GB RAM

Brand: IBM Pages: 2

8676 - Eserver xSeries 335

Brand: IBM Pages: 92

8670 - Eserver xSeries 345

Brand: IBM Pages: 60

8647 - Eserver xSeries 225

Brand: IBM Pages: 182

8480 - Eserver xSeries 205

Brand: IBM Pages: 64

Brand: IBM Pages: 2

Brand: IBM Pages: 136

Brand: IBM Pages: 480

Brand: IBM Pages: 68

@Server pSeries 630 6C4

Brand: IBM Pages: 180

eServer 380 xSeries

Brand: IBM Pages: 54

ioLogik W5300 Series

Brand: Moxa Technologies Pages: 177

UniServer R4900 G5

Brand: H3C Pages: 141

Brand: ONELAN Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands