Altigen ACC 6.7 Administration Manual Download Page 39 | Manualshive

Page: 39 / 462

background image

Chapter 2: System Requirements and Installation

MAXCS ACC 6.7 Administration Manual 25

–

When using a soft system key, the MaxCS system must be a member of an
Active Directory domain.

•

Software license key

—A 20-digit key located on the front of the End User License

Agreement.

Installing MAX Communication Server

To install MAXCS, insert the MAXCS 6.7 CD ROM into the CD ROM drive of the server,
and follow the instructions on the install screens. At the third screen, select a setup type:

•

All-in-one (Stand Alone) System Installation

—Select this option if MAXCS ACC

will be operating on a single server. (This is the most common installation option.)

•

Multi-Gateway Softswitch System Installation

—Select this option if the

Softswitch, Media Server, and gateway(s) will be running in different chassis in an
enterprise deployment. On the next screen you can select which components to
install.

•

Redundant System Installation

—Select this option if you are setting up a

redundant system. On the next screen you can select the components to install.

Multi-Gateway Softswitch System Installation

These are the components you have to choose from.

«
...
37
38
39
40
41
...
»

Summary of Contents for ACC 6.7















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ACC 6.7

Brand: IBM Pages: 214

Brand: IBM Pages: 214

totalstorage 200

Brand: IBM Pages: 152

Brand: IEI Technology Pages: 89

System x3250 M3 Type 4251

Brand: IBM Pages: 32

Brand: Raidon Pages: 20

Brand: HPE Pages: 4

Brand: QNAP Pages: 58

Brand: SMART-AVI Pages: 43

WPS54GU2 - Wireless-G PrintServer For USB 2.0 Print Server

Brand: Linksys Pages: 76

WPSM54G - Wireless-G PrintServer With Multifunction Printer Support Print Server

Brand: Linksys Pages: 132

Brand: High End Systems Pages: 224

Brand: Red Hat Pages: 120

Brand: DSP4YOU Pages: 28

Brand: Gigabyte Pages: 104

ProxyServer MTPSR1-100

Brand: Multitech Pages: 16

MultiArrayIII MA3a

Brand: Multitech Pages: 40

Brand: Multitech Pages: 82

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands