Altigen ACC 6.7 Administration Manual Download | Manualshive

Page: 311 / 462

background image

Chapter 24: Network Configuration Guidelines for VoIP

MAXCS ACC 6.7 Administration Manual 297

The NIC in both the MAXCS server and the IPTalk client (used with MaxCommunicator/
MaxAgent) must support 802.1p. To see if the NIC supports the 802.1p feature, open
the NIC’s Properties dialog box and select the

Advanced

tab. See if the "QoS Packet

Tagging" property is in the Property list. (Different NICs have different properties and
may display a different property name for the 802.1p feature.) If the NIC supports the
802.1p feature, the default value is

Disabled

and you can change this value to enable

802.1p as seen in the following figure:

Once the 802.1p property is enabled, the operating system should notify the NetFilter
driver whether the NIC supports the 802.1p feature.
For 802.1p, eight different classes of service are available, expressed through the 3-bit
user priority field in an IEEE 802.1Q header added to the frame. In MAXCS, 802.1p
tagging is implemented in the NetFilter driver in the server side applying QoS tagging to
the voice packet. The IP phone tags the voice packet from the ARM processor with a user
configured value.

To specify the priority value

The server side configuration is located in the HMCP board's

Board Configuration

settings or the VoIP board’s

Board Configuration > Advanced setting

:

In MaxCommunicator/MaxAgent, the configuration is in the IPTalk configuration screen:

«
...
309
310
311
312
313
...
»

Summary of Contents for ACC 6.7















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ACC 6.7

Express5800/180Ra-7

Brand: NEC Pages: 2

Express5800/120Rh-2

Brand: NEC Pages: 2

Express5800/120Rh-2

Brand: NEC Pages: 2

Express5800/120Rg-1

Brand: NEC Pages: 2

Express5800/120Rf-1

Brand: NEC Pages: 21

Express5800/120Ra-1

Brand: NEC Pages: 6

Express5800/120Mc2 series

Brand: NEC Pages: 2

EXPRESS5800/120Le

Brand: NEC Pages: 56

Express5800 320La

Brand: NEC Pages: 8

Express5800 120Li

Brand: NEC Pages: 2

Express5800 120Ed

Brand: NEC Pages: 29

Active Upgrade Express5800/320Fc

Brand: NEC Pages: 4

Brand: NEC Pages: 10

Express5800/120Rj-2

Brand: NEC Pages: 18

Express5800/120Rh-1

Brand: NEC Pages: 20

Bull NovaScale R620 Series

Brand: NEC Pages: 346

Express5800 320La

Brand: NEC Pages: 206

Express5800/R110j-1

Brand: NEC Pages: 30

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands