GEA Omni страница 210 Скачать руководство пользователя | Manualshive

Страница: 210 / 238

background image

Shutdown

Explanation

Low Outlet Temperature Shut-
down

This annunciation will be triggered if the outlet temperature reading falls
below the value of the

Low Outlet Temperature Shutdown

parameter. This

shutdown will only be annunciated if the compressor is in the starting or run-
ning states.

Zero Load Shutdown

This annunciation will be triggered if the compressor is running and the
capacity slide remains below the zero load position for a set period of time.

No Oil Flow Detected Shutdown This annunciation will be triggered if the flow switch in the compressor hous-

ing becomes de-energized while the compressor is running, or if the switch
does not become energized within a set period of time once the compressor
is started. This annunciation will only be enabled for Sabroe compressors.

Power Reset Abort Shutdown

This annunciation will be triggered if the duration of a power outage exceeds
the value of the

Power Failure Restart Abort Timer

. This annunciation will

only be issued if the

Power Failure Restart Mode

parameter is not to

Disa-

bled

.

Pump Down Too Long Shut-
down

This annunciation will be triggered if the compressor remains in

Pump Down

mode for a period of time in excess of the value entered in the

Pump Down

Maximum Time

parameter.

Discharge Check Valve Failed
To Open Shutdown

This annunciation will be triggered if the discharge valve did not open when
instructed to do so by the panel. This annunciation will only be enabled if the
compressor is equipped with a motorized discharge check valve.

Discharge Check Valve Failed
To Close Shutdown

This annunciation will be triggered if the discharge valve did not close when
instructed to do so by the panel. This annunciation will only be enabled if the
compressor is equipped with a motorized discharge check valve.

Oil Drain Failed To Clear Shut-
down

This annunciation will be triggered if the Oil Drain input does not de-energize
within a set period of time after the compressor is instructed to start. This
annunciation will only be enabled for Hall compressors.

Low Auxiliary Safety Pressure

This annunciation will be triggered if the compressor

Auxiliary Safety Pres-

sure

falls below the value of the

Low Ammonia Storage Pressure Shutdown

parameter.

Low Pressure Differential

This annunciation will be triggered if the difference between the Suction
Pressure and the Discharge Pressure falls below a safe value. This annunci-
ation is for Grasso Compressors only.

Suction Check Valve Failed To
Open

This annunciation will be triggered if, after receiving an instruction to open,
the suction check valve has not indicated that it is fully open within the period
of time defined by the

Suction Check Failed To Open Shutdown Delay

parameter.

Annunciations
Shutdowns

Instruction Manual | GEA Omni™

Control panel

210

GEA Refrigeration North America, Inc. | E_806550_2 | Generated 12.01.2016

«
...
208
209
210
211
212
...
»

Содержание Omni















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Omni

Бренд: Galcon Страницы: 32

Бренд: Lawler Страницы: 6

Бренд: Data Aire Страницы: 28

Бренд: ICP DAS USA Страницы: 166

Бренд: ICP DAS USA Страницы: 64

Tunnel Master Jr

Бренд: ICS Страницы: 83

PROFIBUS PROFI-2510

Бренд: ICP DAS USA Страницы: 4

Бренд: ICP DAS USA Страницы: 40

Бренд: Acuity Controls Страницы: 5

Бренд: Risco Страницы: 232

CompleteStat-Series CS9B-THO

Бренд: Bard Страницы: 2

Бренд: bluelab Страницы: 39

Бренд: SOMFY Страницы: 2

Бренд: Ubiquiti Страницы: 16

Бренд: OmarLift Страницы: 50

Бренд: M-system Страницы: 3

Бренд: Parker Страницы: 8

color LaserJet 5500

Бренд: IBM Страницы: 192

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды