GEA Omni страница 228 Скачать руководство пользователя

Страница: 228 / 238

5.3.1

Compressor Capacity Slide Input Calibration with External Oil Pump

1. Ensure that the control panel is in

Service Mode

and the compressor is

Stopped

2. Touch the

Capacity Slide Position

entry in the

Sensor Calibration

display to bring up the calibration pad.

3. Touch the

OIL PUMP

button. The indicator on the right edge of the button will be illuminated green to

indicate that the oil pump is running. This step may be skipped for Vilter compressors.

4. Touch the

UNLOAD

button. Wait until the slide valve reaches the fully unloaded position, at which point

the value in the

Raw Signal

column should stabilize. The value that the signal will stabilize to is deter-

mined by the type of sensor being used.

Hint!

Certain Compressors will use reverse acting capacity sensors, which will stabilize to a
high value at the low offset.

5. Touch the

Save Low Offset

button. The corresponding slide valve position sensor output has been

recorded as the fully unloaded position.

6. Touch the

LOAD

button. Wait until the slide valve reaches the fully loaded position, at which point the

value in the

Raw Signal

column should stabilize. The value that the signal will stabilize to is determined

by the type of sensor being used.

7. Touch the

Save High Offset

button, the corresponding slide valve position sensor output has been

recorded as the fully loaded position.

8. Touch the

UNLOAD

button again. The compressor should fully unload and the indicated

Capacity Slide

Position

should track with it. Touch the

LOAD

button to fully load the compressor and observe the

Capacity Slide Position

9. If the

Capacity Slide Position

appears to track the

Raw Signal

, the calibration is complete. Turn off the oil

pump by touching the

OIL PUMP

button a second time.

10. Otherwise, repeat the procedure from step #1. Ensure that the slide position indicator reading changes

smoothly between full unload and full load.

11. Exit the calibration pad by touching the

button.

12. The compressor must remain stopped for a period of time determined by the

Oil Drain Timer

5.3.2

Compressor Capacity Slide Input Calibration without External Oil Pump

1. Ensure that the control panel is in

Service Mode

and the compressor is

Stopped

2. Touch the

Capacity Slide Position

entry in the

Sensor Calibration

display to bring up the calibration pad.

Sensor Calibration
Capacity Slide Position Calibration

Instruction Manual | GEA Omni™

Control panel

228

GEA Refrigeration North America, Inc. | E_806550_2 | Generated 12.01.2016

Содержание Omni















































































































































































































































Результаты поиска

Содержание Omni

Отзывы:

Похожие инструкции для Omni

Бренды по названию

Популярные бренды

GEA Omni, Инструкция по эксплуатации

Результаты поиска

Содержание Omni

Отзывы:

Похожие инструкции для Omni

Бренды по названию

Популярные бренды