GEA Omni страница 198 Скачать руководство пользователя | Manualshive

Страница: 198 / 238

background image

8.

Check Slide Position

During this step, the panel will ensure that the position of the capacity slide is below the value of the

Capacity Slide Allowed To Start

parameter.

9.

Retrofit Oil Drain Input Energized

During this step, the panel will wait for the compressor

Oil Drain Input

to become energized. This step will

only be displayed if the compressor

Brand

is set to a

Hall with Internal/No Pump

in the configuration.

10.

Check Prelube Timer (optional)

During this step, the oil pump will be run for a period of time specified in the

Oil Pump Prelube Timer

param-

eter. This step will not be displayed if the compressor is set to a

Grasso

in the configuration.

11.

Check Oil Differential

During this step, the panel will check to ensure that the oil differential pressure is at an acceptable value.

12.

Send Motor Start Signal

During this step, the panel will energize the compressor motor starter output.

13.

Check Interlock

During this step, the panel will check to ensure that the motor starter interlock has become energized within
an appropriate amount of time and that the motor current reading is at an acceptable value.

3.9.3

Running Description

This mode of operation indicates that the compressor has successfully started. As long as it remains in this
mode, the compressor will operate normally as dictated by the capacity control parameters. While in this mode,
the green

START

button will be solidly illuminated.

3.9.4

Stopping Description

This mode of operation indicates that the compressor is in the process of stopping. During this period, the com-
pressor will unload to its minimum position before stopping the compressor. While the panel is in this mode, the

STOP

button will be blinking.

The stopping sequence follows the steps displayed below:

1.

Check Slide Position

During this step, the panel will ensure that the position of the capacity slide is below the value of the

Capacity Slide Allowed To Start

parameter.

2.

Send Motor Stop Signal

During this step, the panel will send the command to stop the compressor.

3.

Check Interlock

During this step, the panel will check to ensure that the motor starter interlock has become de-energized
within an appropriate amount of time and that the motor current reading is at an acceptable value.

3.10

Additional Operating States

This section details additional compressor states which may occur during operation.

Control
Additional Operating States

Instruction Manual | GEA Omni™

Control panel

198

GEA Refrigeration North America, Inc. | E_806550_2 | Generated 12.01.2016

«
...
196
197
198
199
200
...
»

Содержание Omni















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Omni

Бренд: DAV TECH Страницы: 10

Бренд: Unitech Страницы: 11

Бренд: B meters Страницы: 10

Бренд: Calpeda Страницы: 4

Бренд: fakro Страницы: 16

Бренд: e-BLEACH Страницы: 24

Бренд: York Страницы: 24

Бренд: Zamel Страницы: 23

Бренд: Zamel Страницы: 2

Бренд: Zamel Страницы: 2

Бренд: Zander Aachen Страницы: 44

Extra Free ROB-01/12-24V

Бренд: Zamel Страницы: 2

Бренд: Zamel Страницы: 14

Бренд: Absima Страницы: 5

Q Module WFZ16.Ox

Бренд: QUNDIS Страницы: 24

Бренд: Apex Toys Страницы: 7

Бренд: FrSky Страницы: 2

Бренд: Rain Bird Страницы: 48

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды