GEA Omni Скачать руководство пользователя | Manualshive

Страница: 124 / 238

background image

4.

Oil Pump Drain Timer

This parameter is used to select the amount of time the compressor must wait whenever oil must be drained
from the system before it will be permitted to start. The value is measured in minutes.

5.

Oil Pump Compressor Allowed Start Timer

This parameter is used to select the period of time within which the oil pump may run and the compressor is
still permitted to start. If this time period is exceeded, the oil must be drained before the compressor may
start. The value is measured in seconds.

6.

Oil Pump Prelube Timer

This parameter is used to select the period of time that the oil pump will run before the compressor is
started. This parameter is not used on Grasso compressors. The value is measured in seconds.

7.

Oil Pump Postlube Timer

This parameter is used to select the period of time that the oil pump will remain running after the compressor
has stopped. This parameter is not used on Grasso compressors. The value is measured in seconds.

8.

Oil Pump Run Minimum Timer

This parameter is used to select the minimum amount of time that the oil pump must run when it is started
based on low differential pressure. It will only appear if the oil pump type is set to

External Cycling

in the

configuration. The value is measured in seconds.

9.

Oil Pump Cycle On

This parameter is used to select the oil differential above which the oil pump will start. It will only appear if
the oil pump type is set to

External Cycling

in the configuration. The value is measured in seconds.

10.

Oil Pump Cycle Off

This parameter is used to select the oil differential below which the oil pump will stop after the time period
defined by the

Oil Pump Run Minimum Timer

haselapsed. It will only appear if the oil pump type is set to

External Cycling

in the configuration. The value is measured in seconds.

11.

Oil Pump Lead Selection

This parameter is used to select whether

Pump 1

or

Pump 2

is considered the lead pump. This parameter is

only visible if the

Dual Oil Pump

option is selected in the

Oil System Details

section of the configuration. The

options are:

•

Pump 1

•

Pump 2

12.

Oil Pump Maintained Timer

This parameter is used to select the period of time during startup that the oil pump must maintain a valid oil
differential pressure value before the compressor will be permitted to start. This parameter is fixed on
Grasso compressors and will not be visible. The value is measured in seconds.

Control
Compressor Control Parameters

Instruction Manual | GEA Omni™

Control panel

124

GEA Refrigeration North America, Inc. | E_806550_2 | Generated 12.01.2016

«
...
122
123
124
125
126
...
»

Содержание Omni















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Omni

Бренд: ABB Страницы: 52

Бренд: ABB Страницы: 2

Бренд: Balboa Страницы: 12

Бренд: Paoli Страницы: 16

Бренд: IBM Страницы: 144

Бренд: Warren Controls Страницы: 16

Бренд: Wavelink Страницы: 69

Бренд: Watlow Страницы: 59

Tekmar WiFi Snow Melting Control 670

Бренд: Watts Страницы: 48

Бренд: PUTCO Страницы: 2

Бренд: Absima Страницы: 5

Бренд: zeeltronic Страницы: 15

Бренд: M-system Страницы: 3

MP23xxxiec Series

Бренд: YASKAWA Страницы: 102

Бренд: O&O Страницы: 64

Бренд: ARI-Armaturen Страницы: 17

Бренд: Hasco Страницы: 78

Бренд: Maintronic Страницы: 53

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды