GEA Omni Скачать руководство пользователя | Manualshive

Страница: 105 / 238

background image

Parameter

Units

Minimum

Maximum

Default

Maximum Capacity Slide Position

Percent

See Description

100 %

100 %

Ramp Rate Per Minute

Dependent on Control Signal. Refer to Panel Data Report

1.

Name

This parameter contains the name used to identify the specific set of capacity control parameters. The user
may modify it by entering a desired text string into this parameter.

2.

Control Signal

This parameter is used to set which input will be monitored to control the capacity slide valve of the com-
pressor. The options are:

•

Suction Pressure

•

Suction Pressure as Temperature

•

Inlet Temperature

•

Outlet Temperature

•

Discharge Pressure

•

Discharge Pressure as Temperature

•

Remote Capacity Slide

•

Remote Temperature

•

Remote Pressure

Hint!

If this parameter is changed to an option with a different unit type, the Set point, Dead Band
and Proportional Band will be reset to their default values.

3.

Set Point

This parameter is used to choose the desired value at which the compressor will attempt to maintain the
control signal. The user may change this parameter by entering a new value with the keypad. The maximum
value, minimum value and units of the parameter are dependent on the chosen control signal:

•

Pressure

Measured in the panel pressure units as selected in the

Panel Settings

screen.

•

Temperature

Measured in the panel temperature units as selected in the

Panel Settings

screen.

•

Remote Capacity Slide

Measured in percent.

Instruction Manual | GEA Omni™
Control panel

Control

Compressor Control Parameters

GEA Refrigeration North America, Inc. | E_806550_2 | Generated 12.01.2016

105

«
...
103
104
105
106
107
...
»

Содержание Omni















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Omni

Бренд: VADDIO Страницы: 2

Бренд: Valor Страницы: 20

Бренд: Daikin Страницы: 5

Бренд: OES Страницы: 3

Бренд: Balboa Страницы: 74

Бренд: Cadac Страницы: 4

Бренд: +GF+ Страницы: 3

Бренд: Össur Страницы: 58

Бренд: Savant Страницы: 2

Бренд: HBM Страницы: 88

Бренд: Current Страницы: 4

Бренд: PEAS Страницы: 4

Бренд: Sollae Systems Страницы: 72

Бренд: Viper Страницы: 2

Бренд: PXM Страницы: 15

Бренд: Parker Страницы: 8

color LaserJet 5500

Бренд: IBM Страницы: 192

AUMATIC ACExC 01.2

Бренд: AUMA Страницы: 92

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды