GEA Omni Скачать руководство пользователя

Страница: 221 / 238

4.2.5

List and Description of Profibus Gateway Warnings

Warning

Explanation

Lost Communication With Gate-
way

This annunciation will be triggered if the communications between the GEA
Omni™ panel and the Profibus Gateway are interrupted.

LiveBit Time Communication
With Gateway

This annunciation will be triggered if the Livebit is not changing while com-
munication with the Profibus Gateway.

4.2.6

List and Description of GEA BluAstrum Condenser Warnings

Warning

Explanation

Condenser No Coolant Flow
Detected

This annunciation will be triggered if no coolant flow is detected in the con-
denser.

Condenser High Temperature

This annunciation will be triggered if the temperature in the condenser
exceeds the value of the

High Condenser Temperature Warning

parameter.

4.2.7

List and Description of VTrac Warnings

Warning

Explanation

High Vibration Warning

This annunciation will be triggered if the vibration measured by the VTrac
monitor has exceeded the safe range.

VTrac High Vibration Damage
Warning

This annunciation will be triggered if the vibration measured by the VTrac
monitor has become severe enough that continued operation could damage
the equipment. This annunciation will only occur if VTrac shutdowns are dis-
abled.

VTrac No Communications

This annunciation will be triggered if the communications between the GEA
Omni™ panel and the VTrac vibration monitor are interrupted.

Instruction Manual | GEA Omni™
Control panel

Annunciations

Warnings

GEA Refrigeration North America, Inc. | E_806550_2 | Generated 12.01.2016

221

Содержание Omni















































































































































































































































Результаты поиска

Содержание Omni

Отзывы:

Похожие инструкции для Omni

Бренды по названию

Популярные бренды

GEA Omni, Инструкция по эксплуатации

Результаты поиска

Содержание Omni

Отзывы:

Похожие инструкции для Omni

Бренды по названию

Популярные бренды