manualshive.com logo in svg

GEA Omni, Инструкция по эксплуатации

Instant Omni - многофункциональное устройство, которое позволяет готовить еду быстро и легко. Для получения дополнительной информации и инструкций по использованию, загрузите бесплатное руководство пользователя на нашем сайте. Удобный и надежный способ овладеть всеми функциями устройства.

Поделиться
Скачать
background image

3.9

Normal Operating States

This section details the four normal compressor states which the compressor may be in while a shutdown condi-
tion has not been annunciated.

3.9.1

Stopped Description

This mode of operation indicates that the compressor is not running and automatic start is disabled. While the
panel is in this mode, the red 

STOP

 button will be solidly illuminated.

3.9.2

Starting Description

This mode of operation indicates that the compressor is in the process of starting. During this period, the com-
pressor will unload to its minimum position. The compressor will remain in this mode as long as the conditions
required for the compressor to start are not met and the compressor has not entered a shutdown condition.
While the panel is in this mode, the green 

START

 button will be blinking.

The starting sequence follows the steps displayed below:

1.

Check Oil Pump Circulation (optional)

During this step, the panel will check that the oil temperature is greater than or equal to the value of the 

Oil

Pump Circulation Temperature Set Point

. If the oil temperature does not meet this condition, the oil pump will

run to attempt to bring the temperature reading up to the appropriate value. If the temperature has not
reached the selected value after a period of time specified in the 

Oil Pump Circulation Shutdown Timer

parameter, a shutdown will be annunciated. This step will only be displayed if the 

Oil Pump Circulation Mode

parameter is set to 

Temperature

.

2.

Check Drive Conditions

During this step, the panel will check that the time periods specified for example in the 

Motor Start To Start

Timer

 and 

Motor Stop To Start Timer

 parameters have elapsed.

3.

Check Oil Drain Timer

During this step, the panel will check whether the compressor must be drained of oil before being permitted
to start. If the oil must be drained, the compressor will wait until the time period specified in the 

Oil Drain

Timer

 parameter has elapsed.

4.

Check Control Signal Cycling

During this step, the panel will check the conditions of the compressor to ensure that the control value is in a
valid state to start. This step will only be displayed if the 

Automatic Start Stop

 parameter is set to 

Enabled

.

5.

Check Permissive Start

During this step, the panel will wait for the permissive start signal to become energized.

6.

Check Pump Down Build To Pressure

During this step, the compressor will wait until the compressor suction pressure has risen to an acceptable
value. This step will only be displayed if the 

Pump Down Mode

 is set to 

Automatic

 in the configuration.

7.

Check Discharge Check Valve

During this step, the panel will check to ensure that the motorized discharge check valve, if applicable, has
opened within an acceptable period of time.

Instruction Manual | GEA Omni™
Control panel

Control

Normal Operating States

GEA Refrigeration North America, Inc. | E_806550_2 | Generated 12.01.2016

197

Содержание Omni















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Omni

Gardena 4040 Operating Instructions Manual preview
4040
Бренд: Gardena Страницы: 100
IBM 1710 Manual preview
1710
Бренд: IBM Страницы: 72
Tapeswitch C6 Technical Manual preview
C6
Бренд: Tapeswitch Страницы: 13
Samsung SolarCell Remote Instructions preview
SolarCell Remote
Бренд: Samsung Страницы: 2
Samsung MWR-SH11N Installation Manual preview
MWR-SH11N
Бренд: Samsung Страницы: 20
Rain Bird PAR+ES Installation Manual preview
PAR+ES
Бренд: Rain Bird Страницы: 24
Rain Bird ESP-LXIVM Series Device Installation Manuallines preview
ESP-LXIVM Series
Бренд: Rain Bird Страницы: 16
Rabe PILOT Original Instructions Manual preview
PILOT
Бренд: Rabe Страницы: 61
Racal Instruments 1260 VXI Instructions Manual preview
1260 VXI
Бренд: Racal Instruments Страницы: 35
Samson FOUNDATION 3730-5 Mounting And Operating Instructions preview
FOUNDATION 3730-5
Бренд: Samson Страницы: 132
Samson 3767 Mounting And Operating Instructions preview
3767
Бренд: Samson Страницы: 68
Samson 3730-2 Mounting And Operating Instructions preview
3730-2
Бренд: Samson Страницы: 128
Samson 3725 series Mounting And Operating Instructions preview
3725 series
Бренд: Samson Страницы: 68
X-POWER MULTI 1 Instruction And Installation Manual preview
MULTI 1
Бренд: X-POWER Страницы: 24
Samson TROVIS 3730-1 Mounting And Operating Instructions preview
TROVIS 3730-1
Бренд: Samson Страницы: 80
Haehne DCX Quick Start Manual preview
DCX
Бренд: Haehne Страницы: 44
Xylem FST Installation, Operation And Maintenance Manual preview
FST
Бренд: Xylem Страницы: 48
Parker EP Series Pro-Bloc Installation And Operation Manual preview
EP Series Pro-Bloc
Бренд: Parker Страницы: 11

Бренды по названию

Популярные бренды

Загрузить еще бренды