GEA Omni Скачать руководство пользователя | Manualshive

Страница: 222 / 238

background image

4.2.8

List and Description of Refrigerant Sensor Warnings

Warning

Explanation

Refrigerant Sensor High Warn-
ing

This annunciation will be triggered if the parts per million reading on any
refrigerant sensor exceeds the

Refrigerant Sensor High Warning

parameter

for the period of time defined by the

Refrigerant Sensor High Warning Delav’

parameter.

Refrigerant Sensor High High
Warning

This annunciation will be triggered if the parts per million reading on any
refrigerant sensor exceeds the

Refrigerant Sensor High High Warning

parameter for the period of time defined by the

Refrigerant Sensor High High

Warning Delay

parameter.

4.2.9

List and Description of Oil Still Warnings

Warning

Explanation

No Oil Still Return Activated

This annunciation will be triggered if the Oil Return attempts to initiate while
no compressors are running.

4.2.10

List and Description of Other Warnings

Warning

Explanation

Auxiliary Warning

This annunciation will be triggered if the Auxiliary Warning input becomes de-
energized. This warning will only be issued if the Auxiliary Warning option
has been enabled in the configuration.

Math Block Units Mismatch
Warning

This annunciation will be triggered if the inputs of a Math block in the logic
diagram are expressed in different units.

Sensor Failure Warning

This annunciation will be triggered if the reading of a sensor is outside its
defined range. This annunciation will be triggered if the compressor can con-
tinue to run safely without the failed sensor.

Please contact GEA High Log
Usage

This annunciation will be triggered if an unusual amount of information is
being written to the activity log.

Math Block Units Mismatch

This annunciation will be triggered if a Math block in the logic diagram is
receiving two different unit types as input.

Annunciations
Warnings

Instruction Manual | GEA Omni™

Control panel

222

GEA Refrigeration North America, Inc. | E_806550_2 | Generated 12.01.2016

«
...
220
221
222
223
224
...
»

Содержание Omni















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Omni

Бренд: DAV TECH Страницы: 10

Бренд: Quectel Страницы: 23

Бренд: Quectel Страницы: 79

Бренд: National Instruments Страницы: 29

Бренд: Harmonic Drive Страницы: 85

Бренд: Jäger Страницы: 50

Бренд: WAREMA Страницы: 112

Бренд: WAGO Страницы: 414

Бренд: V2 Страницы: 48

Бренд: ABB Страницы: 17

Бренд: Climatisation Страницы: 52

Бренд: TECOM Страницы: 8

AQUASNAP 30RA "B"

Бренд: Carrier Страницы: 36

Бренд: YASKAWA Страницы: 92

Бренд: VALPES Страницы: 28

Бренд: Eaton Страницы: 94

Бренд: G-Scale Graphics Страницы: 12

Бренд: Digitrax Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды