GEA Omni Скачать руководство пользователя

Страница: 165 / 238

Parameter

Units

Minimum

Maximum

Default

Condenser Unit Stop Delay

Seconds

0 s

1800 s

0 s

Condenser Flow Switch Warning
Delay

Seconds

0 s

60 s

30 s

Start Condition

This Parameter is used to select the start condition of the condenser.

Feedback Condenser Unit Delay

This Parameter is used to set a delay time. If the compressor is in the state

Starting

Running

the time will

be started. If the time is elapsed before the feedback of the condenser unit is set to true a warning will be
annunciated.

Condenser Unit Stop Delay

This Parameter is used to set a delay time. The time will be started after the compressor state has changed
to

Stopped

. After the time is elapsed the release of the condenser unit will be resettled.

Condenser Flow Switch Warning Delay

This Parameter is used to set a delay time. If the compressor is in the state

Starting

Running

the time will

be started. If the time is elapsed before the condenser flow switch detects flow a warning will be annunci-
ated.

3.5

Evaporator Control Parameters

Control parameters are displayed on the main Evaporator screen detailed in Section 2.7.2, Page 48. Below is a
list of all control parameters and a brief description of their function.

3.5.1

Cooling

Parameter

Units

Minimum

Maximum

Default

Set Point

°C

-56.7 °C

204.4 °C

-1 °C

°F

-70.1 °F

399.9 °F

30.2 °F

Set Point Delay

Seconds

0 s

300 s

5 s

Dead Band

°C

0.00 °C

100 °C

2.0 °C

°F

0.0 °F

180.0 °F

3.6 °F

Temperature High Warning Offset

°C

0.00 °C

40.0 °C

2.0 °C

°F

0.0 °F

72.0 °F

5.0 °F

Instruction Manual | GEA Omni™
Control panel

Control

Evaporator Control Parameters

GEA Refrigeration North America, Inc. | E_806550_2 | Generated 12.01.2016

165

Содержание Omni















































































































































































































































Результаты поиска

Содержание Omni

Отзывы:

Похожие инструкции для Omni

Бренды по названию

Популярные бренды

GEA Omni, Инструкция по эксплуатации

Результаты поиска

Содержание Omni

Отзывы:

Похожие инструкции для Omni

Бренды по названию

Популярные бренды