GEA Omni Скачать руководство пользователя

Страница: 126 / 238

3.1.11

Oil Pump Interlock

Parameter

Units

Minimum

Maximum

Default

Illegal Oil Pump Interlock Shutdown
Timer

Seconds

1 s

60 s

5 s

Oil Pump Loss of Lead Interlock
Warning

Seconds

1 s

60 s

5 s

Oil Pump Loss of Interlock Shut-
down Timer

Seconds

1 s

60 s

5 s

Illegal Oil Pump Interlock Shutdown Timer

This parameter is used to select the amount of time the panel will wait to trigger an

Illegal Oil Pump Interlock

Shutdown

if the oil pump interlock signal is received while the oil pump is not running. The value is meas-

ured in seconds.

Oil Pump Loss of Lead Interlock Warning

This parameter is used to select the period of time that the system will wait before annunciating a

Loss of

Interlock Warning

for the lead oil pump. The parameter will only be visible if the compressor is configured

with dual oil pumps. The value is measured in seconds.

Oil Pump Loss Of Interlock Shutdown Timer

This parameter is used to select the amount of time the panel will wait to trigger a

Loss of Interlock Shut-

down

if the oil pump interlock signal is lost while the oil pump is running. The value is measured in seconds.

3.1.12

Oil Differential Pressure

Parameter

Units

Minimum

Maximum

Default

High Oil Differential Pressure Shut-
down

barG

1.00 barD

See Description

barA

PSIG

14.5 PSID

PSIA

kPaG

100 kPaD

kPaA

MPaG

0.500 MPaD

MPaA

Control
Compressor Control Parameters

Instruction Manual | GEA Omni™

Control panel

126

GEA Refrigeration North America, Inc. | E_806550_2 | Generated 12.01.2016

Содержание Omni















































































































































































































































Результаты поиска

Содержание Omni

Отзывы:

Похожие инструкции для Omni

Бренды по названию

Популярные бренды

GEA Omni, Инструкция по эксплуатации

Результаты поиска

Содержание Omni

Отзывы:

Похожие инструкции для Omni

Бренды по названию

Популярные бренды