GEA Omni страница 192 Скачать руководство пользователя | Manualshive

Страница: 192 / 238

background image

6.

Oil Filter Pressure Transducer

This drop down list is used to select whether the filter is equipped with pressure transducers and where
they are located. The options are:

•

None

•

Inlet

•

Outlet

•

Both

7.

Oil Filter Inlet Scaling

This drop down list is used to select the range of the pressure transducer at the oil filter inlet. This field
will be disabled if no inlet oil pressure transducer is present.

8.

Oil Filter Pressure Drop Max

This text box is used to enter the maximum value for the oil filter pressure parameters. The value is
entered in PSID.

9.

Oil Filter Outlet Scaling

This drop down list is used to select the range of the pressure transducer at the oil filter outlet. This field
will be disabled if no outlet oil pressure transducer is present.

Temperature

This section is a subsection of the oil system. It contains two fields relating to temperature monitoring in the oil
pump system.

10.

Oil Temperature Min

This text box is used to set the minimum value which may be assigned to the oil temperature parame-
ters. The value is measured in degrees Fahrenheit.

11.

Oil Temperature Max

This text box is used to set the maximum value which may be assigned to the oil temperature parame-
ters. The value is measured in degrees Fahrenheit.

Separator

This section is a subsection of the oil system. It contains five fields relating to the operation of the oil separator.

12.

Oil Separator Heaters

This drop down list is used to set the number of heaters that installed on the oil separator.

13.

Oil Separator Temperature Probe

This check box is used to select whether the oil separator is equipped with a dedicated temperature sen-
sor or not.

Control
Configuration

Instruction Manual | GEA Omni™

Control panel

192

GEA Refrigeration North America, Inc. | E_806550_2 | Generated 12.01.2016

«
...
190
191
192
193
194
...
»

Содержание Omni















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Omni

Бренд: Hankscraft Runxin Страницы: 53

Бренд: Danfoss Страницы: 37

Бренд: Daikin Страницы: 44

Бренд: Harman Kardon Страницы: 25

Бренд: Uniss Страницы: 21

Бренд: Dakota Digital Страницы: 12

Бренд: Objective Imaging Страницы: 11

Бренд: Rain Bird Страницы: 11

LOOPDRIVE FIM-RC

Бренд: 4EVAC Страницы: 2

Бренд: CommBox Страницы: 4

Бренд: RDL Страницы: 2

Бренд: OBO Bettermann Страницы: 6

Бренд: NI Страницы: 135

Бренд: fadini Страницы: 40

Бренд: Tactical Страницы: 4

Бренд: Vag Страницы: 4

Бренд: W8ZR Страницы: 77

Бренд: ICP DAS USA Страницы: 9

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды