GEA Omni страница 231 Скачать руководство пользователя

Страница: 231 / 238

5.4

Volume Slide Position Calibration

Touching the cell associated with the measured value of the

Volume Slide Position

will bring up the calibration

display shown below. The functions of the buttons are the same as those discussed in Section 5.3, Page 227

Capacity Slide Position Calibration

. However, the volume slide cannot be calibrated automatically.

fig.119:

Volume Slide Calibration Pad

1. Calibrate or confirm that the primary capacity slide has been calibrated.

2. Put the control panel in

Service Mode

START

the compressor.

4. Touch the

Volume Slide Position

entry to bring up the calibration pad. Automatic or manual control of the

volume slide is suspended.

5. Touch the

UNLOAD

button. Wait until the volume slide reaches the low Vi position. The

Vi Slide Indicator

should stabilize at 4 mA when the slide is completely unloaded.

6. Touch the

Save Low Offset

button, the corresponding slide valve position sensor output has been recorded

as the fully unloaded position.

7. Touch the

LOAD

button. Wait until the Vi slide valve reaches the high Vi position. The

Vi Slide Indicator

should stabilize at 20 mA when the slide is fully loaded.

8. Touch the

Save High Offset

button, the corresponding slide valve position sensor output has been recorded

as the fully loaded position.

9. Touch the

UNLOAD

button again. The volume slide should fully unload and the indicated Vi Slide Position

(%) should track with it.
Touch the

LOAD

button to fully load the volume slide and observe the Vi Slide Position (%).

10. If the

Vi Slide Position

(%) appears to track with the Vi slide indicator, the calibration is complete.

11. Touch the

to close the calibration window.

12. Automatic or manual control will resume depending on the control parameter setting.

13. Calibration of the Vi slide is complete.

14. The compressor may be taken out of

Service

mode and

Stopped

if desired.

Instruction Manual | GEA Omni™
Control panel

Sensor Calibration

Volume Slide Position Calibration

GEA Refrigeration North America, Inc. | E_806550_2 | Generated 12.01.2016

231

Содержание Omni















































































































































































































































Результаты поиска

Содержание Omni

Отзывы:

Похожие инструкции для Omni

Бренды по названию

Популярные бренды

GEA Omni, Инструкция по эксплуатации

Результаты поиска

Содержание Omni

Отзывы:

Похожие инструкции для Omni

Бренды по названию

Популярные бренды