manualshive.com logo in svg

GEA Omni, Инструкция по эксплуатации

Instant Omni - многофункциональное устройство, которое позволяет готовить еду быстро и легко. Для получения дополнительной информации и инструкций по использованию, загрузите бесплатное руководство пользователя на нашем сайте. Удобный и надежный способ овладеть всеми функциями устройства.

Поделиться
Скачать
background image

2.

Motorized Liquid Injection Valve Temperature Set Point

This parameter is used to set the desired temperature value of the selected control signal that the modulat-
ing valve will attempt to maintain for oil cooling control. This parameter will only be visible if oil cooling type is
set to 

IntelliSOC™

 in the configuration. The value is measured in the panel temperature units as selected on

the 

Panel Settings

 screen.

3.

Minimum Valve Position

This parameter is used to set the minimum value that the motorized liquid injection valve may be set to when
the compressor is not running. This parameter will only be visible if oil cooling type is set to 

IntelliSOC™

 in

the configuration. The value is measured in percent.

4.

Proportional Term

This parameter is used to set the proportional gain for PI control of the valve position. This value is multiplied
by the total error between the current and desired speed values. This parameter will only be visible if oil cool-
ing type is set to 

IntelliSOC™

 in the configuration. The value is unitless.

5.

Integral Term

This parameter is used to set the rate at which the motor PI controller will change its integral gain base on
the calculated error over time. This parameter will only be visible if oil cooling type is set to 

IntelliSOC

™ in

the configuration. The value is measured in samples per Repeat (s/R).

6.

Mode

This parameter is used to select whether the PI controller will vary its output automatically or if it will be con-
trolled manually through the 

Manual Mode Position

 parameter. This parameter will only be visible if oil cool-

ing type is set to 

IntelliSOC™

 in the configuration. The options are:

•

Auto

•

Manual

7.

Manual Mode Position

This parameter is used to set the desired output of the PI controller while it is set to operate in manual mode.
This parameter will only be visible if oil cooling type is set to 

IntelliSOC™

 in the configuration. The value is

measured in percent.

8.

Calibrate Time Before Bleed

This parameter is used to set the period of time the motorized valve will remain fully unloaded at its 4 mA
position after the compressor is stopped. This parameter will only be visible if oil cooling type is set to 

Intelli-

SOC™

 in the configuration. The value is measured in seconds.

9.

Liquid Injection Begin

This parameter is used to select the temperature of the selected control signal at which the liquid cooling
process will begin. This parameter will only be visible if the oil cooling mode is not set to 

IntelliSOC™

. The

value is measured in the panel temperature units as selected on the 

Panel Settings

 screen.

10.

Liquid Injection End

This parameter is used to select the temperature of the selected control signal below which the liquid cooling
process will end. The value is measured in the panel temperature units as selected on the 

Panel Settings

screen.

11.

Liquid Injection Pulse Period

This parameter is used to select the pulse period of the Liquid Injection Solenoid. The parameter will only be
visible if the oil cooling type is set to 

Yosaku Pulsed Liquid Injection

 in the configuration. The value is meas-

ured in seconds.

Control
Compressor Control Parameters

Instruction Manual | GEA Omni™

Control panel

144

GEA Refrigeration North America, Inc. | E_806550_2 | Generated 12.01.2016

Содержание Omni















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Omni

ZIMO MX10 Instruction Manual preview
MX10
Бренд: ZIMO Страницы: 38
Daikin Madoka User Manual preview
Madoka
Бренд: Daikin Страницы: 2
Daikin BRC7E530W8 Operation Manual preview
BRC7E530W8
Бренд: Daikin Страницы: 12
Daikin BRC1H81K Installation And Operation Manual preview
BRC1H81K
Бренд: Daikin Страницы: 12
Daikin BRC1H71W Operation Manual preview
BRC1H71W
Бренд: Daikin Страницы: 46
Daikin BRC1D71 Operation Manual preview
BRC1D71
Бренд: Daikin Страницы: 21
Daikin BRC1D517 Operation Manual preview
BRC1D517
Бренд: Daikin Страницы: 20
Magellan MG5000 Programming Manual preview
MG5000
Бренд: Magellan Страницы: 44
Namron ZigBee Quick Start Manual preview
ZigBee
Бренд: Namron Страницы: 3
RAKwireless RAK3172 User Manual preview
RAK3172
Бренд: RAKwireless Страницы: 6
Valcom V-2000 Manual preview
V-2000
Бренд: Valcom Страницы: 6
Audioaccess PX-700 Manual preview
PX-700
Бренд: Audioaccess Страницы: 2
FEAS SSE10 Operating Instructions preview
SSE10
Бренд: FEAS Страницы: 4
Danfoss ChangeOver6 Operating Manual preview
ChangeOver6
Бренд: Danfoss Страницы: 2
S&C IntelliCap Operation preview
IntelliCap
Бренд: S&C Страницы: 26
IBCcontrol MicroMax180 Manual preview
MicroMax180
Бренд: IBCcontrol Страницы: 16
Intermatic T30000R SERIES Installation, Operation & Service Manual preview
T30000R SERIES
Бренд: Intermatic Страницы: 3
Gimenez Ganga Saxun Mosquito Screen Lateral Door 2020 Assembly Manual preview
Saxun Mosquito Screen Lateral Door 2020
Бренд: Gimenez Ganga Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды