GEA Omni Скачать руководство пользователя | Manualshive

Страница: 13 / 238

background image

1

SAFETY AND CONFORMITY

1.1

Safety Instructions

The GEA Omni™ is reliable in operation if used as specified.

Hint!

Read the safety instructions in the GEA Omni™ operating manual before startup.

The intended use includes the observance and compliance of

•

all notices regarding hazard to persons and damage to property in the operating instructions,

•

the country-specific standards and safety regulations,

•

the instruction for installation, operation and maintenance,

•

the details of certificates,

•

the requirements for personnel,

•

the obligation to exercise due care.

Only compliance with all provisions and guidelines will enable optimum protection of the personnel as well as
dangers to the environment and the safe and smooth operation of the GEA Omni™.

Warning!

GEA Omni™ can cause hazard in case of improper or unintended use. A malfunction indica-
tion on the touch screen cannot be ignored.
A personal injury or damage to the machine or plant can be the result.
For precautions to prevent danger see safety instructions in the operating manual.

Warning of electric shock!
Danger of electric shock exists.
More than one switch-disconnect may be necessary to isolate all electrical components.
Before maintenance work on the control panel, make sure that all electrical components are
switched off.

Danger!

It should be ensured at any time that all are necessary processes for compressor cooling and
lubrication in operation as long as the compressor is in operation.
This applies esprecially for the case where the compressor is unintentionally in operation. The
unintentionally compressor operation can be determined by observation of the compressor
motor feedback, the motor current or the motor speed.

Instruction Manual | GEA Omni™
Control panel

Safety and Conformity

Safety Instructions

GEA Refrigeration North America, Inc. | E_806550_2 | Generated 12.01.2016

13

«
...
11
12
13
14
15
...
»

Содержание Omni















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Omni

Бренд: GE Страницы: 8

Бренд: Ransburg Страницы: 49

Бренд: Balboa Страницы: 2

Бренд: Badger Meter Страницы: 20

Бренд: K&K Страницы: 6

Бренд: LAS Страницы: 6

Бренд: CORNING Страницы: 12

Бренд: Osaka Страницы: 12

Бренд: Xantech Страницы: 7

Бренд: Chamberlain Страницы: 1

Бренд: Geberit Страницы: 12

multicomp F144-MS-1V1C1TI6RO-3

Бренд: KBR Страницы: 68

Бренд: NCE Страницы: 4

RISC Module SOM-A2552

Бренд: Advantech Страницы: 40

Бренд: Danfoss Страницы: 20

Automation PC 810

Бренд: B&R Страницы: 428

Бренд: Potter Страницы: 4

Vesta Building Controller

Бренд: Vestamatic Страницы: 38

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды