GEA Omni страница 194 Скачать руководство пользователя | Manualshive

Страница: 194 / 238

background image

1.

Drive

This drop down list is used to select the type of motor used in the package.

2.

Motor Current Input

This drop down list is used to select the type of the current input for the motor

3.

Motor Speed Input

This check box is used to select if the panel is equipped with an input to control motor spe

4.

Motor Speed Maximum

This text box is used to enter the maximum allowable speed for the compressor motor. This option is
only used if the compressor is equipped with a variable speed motor. The value is entered in rpm.

5.

Motor RPM for Fixed Speed

This text box is used to enter the desired speed for the compressor motor. This option is only used if the
compressor is equipped with a fixed speed motor. The value is entered in rpm.

6.

Motor Speed Minimum

This text box is used to enter the minimum allowable speed for the compressor motor. This option is only
used if the compressor is equipped with a variable speed motor. The value is entered in rpm.

7.

Min Motor Start To Start Delay

This text box is used to set the minimum amount of time after it has started, measured in minutes, that
the motor must wait before starting again.

8.

Motor Starter Communication Enabled

This check box is used to enable the direct control of a Benshaw motor starter using serial Modbus.

9.

Power Calculation

This drop down list is used to select how the motor’s power is calculated. The options are:

•

None

•

Motor Current Input

•

Direct Analog Input

10.

CT Location

This drop down list is used to select where on the package the current transformer is located. This option
may not be modified in the field.

11.

Motor Space Heater

This is used to select the voltage required by the motor heater, if available. This option may not be modi-
fied in the field.

12.

Package Mounted Starter

This is used to select whether a motor starter is mounted on the package.

Control
Configuration

Instruction Manual | GEA Omni™

Control panel

194

GEA Refrigeration North America, Inc. | E_806550_2 | Generated 12.01.2016

«
...
192
193
194
195
196
...
»

Содержание Omni















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Omni

Бренд: ABB Страницы: 63

Бренд: Abicor Binzel Страницы: 8

Бренд: Calpeda Страницы: 4

Бренд: Eaton Страницы: 100

Бренд: Farfisa Страницы: 20

Бренд: Racal Instruments Страницы: 64

Бренд: Samson Страницы: 32

Бренд: Quantum Страницы: 15

Бренд: Lawler Страницы: 5

Бренд: Quectel Страницы: 90

Compact Comfort VAV12

Бренд: SAI HVAC Страницы: 16

Бренд: saia-burgess Страницы: 203

Бренд: Sailor Страницы: 1

Бренд: WABCO Страницы: 4

Бренд: Rayrun Страницы: 4

Бренд: Parker Страницы: 29

HydroTap G5 Touch-Free Wave

Бренд: Zip Страницы: 24

Бренд: Parker Страницы: 54

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды