GEA Omni страница 47 Скачать руководство пользователя | Manualshive

Страница: 47 / 238

background image

•

A manual initiate triggered through either the touch screen or communications.

•

An automatic defrost based on the run time of the zone’s liquid solenoid.

•

A daily defrost based on the current time of day.

With any of the modes of defrosting, the zone is placed into defrost immediately if no other zone on the same
group is defrosting. If another zone on the same group is in defrost, the zone will instead be placed into pending
defrost until the zone currently defrosting has completed the cycle.
The defrosting cycle may contain up to twelve stages. The amount of time the zone will remain in each stage is
user adjustable.

2.7.1

Overview tab

fig.42:

Evaporator Overview Tab

This screen normally contains a tile display which represents the evaporator system. Each tile represents an
individual zone and displays the zone name, current temperature, set point, current status and defrost group.
The color of each tile indicates the current status of the associated zone. The colors are:

•

Grey:

Disabled

•

Dark Green:

Stopped/ Waiting to Start

•

Light Green:

Starting

•

Light Blue:

Cooling

•

Dark Red:

-Defrost

•

Light Red:

Zone Shutdown

•

Yellow:

Zone Warning

Touching a tile will open the Main Tab of the Evaporator Screen, detailed in Section 2.7.2, Page 48 below.
The behavior and view on this screen may be modified using the buttons found in the lower right hand corner of
the window. The functions of the buttons are detailed below.

Instruction Manual | GEA Omni™
Control panel

User interface

Evaporator

GEA Refrigeration North America, Inc. | E_806550_2 | Generated 12.01.2016

47

«
...
45
46
47
48
49
...
»

Содержание Omni















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Omni

imageRUNNER ADVANCE C9075S PRO

Бренд: Canon Страницы: 20

Бренд: Samson Страницы: 20

Бренд: Samsung Страницы: 32

Бренд: Lawler Страницы: 5

Бренд: Sanhua Страницы: 3

Бренд: Vaillant Страницы: 11

Бренд: Watts Страницы: 4

Бренд: WaterCop Страницы: 4

Бренд: WAREMA Страницы: 4

Бренд: Bartlett Страницы: 7

Бренд: L-Acoustics Страницы: 24

Бренд: L-Acoustics Страницы: 21

Бренд: M&S Systems Страницы: 4

Бренд: Dakota Digital Страницы: 12

Бренд: Samson Страницы: 102

Бренд: Paser Страницы: 2

Бренд: Grundfos Страницы: 80

BLEUBOX R-IN-UHF-5239U

Бренд: iDTRONIC Страницы: 13

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды