manualshive.com logo in svg

GEA Omni, Инструкция по эксплуатации

Поделиться
Скачать
GEA Omni Скачать руководство пользователя страница 234

6. Verify that the compressor is physically fully unloaded. The GEA Omni™ will prevent the compressor from

starting if the slide valve position displayed is greater than 70 %. The 

Slide Valve Position

 may need to be

temporarily recalibrated to 0 % to allow the machine to start.

7. Start the compressor and wait until the compressor is running and oil pressure has been established.

8. Touch the 

UNLOAD

 button and wait about 90 seconds for the slide valve to fully unload. Smaller machines

may not require the full 90 seconds to unload.

9. The calibration button on the transducer is positioned between the two LEDs. Push and hold the calibration

button for five seconds, both LEDs should be off.

10. Press the pushbutton one time and release it. The red LED will now turn 

On

, and remain 

On

, for approxi-

mately 3 seconds while the zero calibration point is stored. 

DO NOT

 move the slide valve until the red LED

turns off.

11. Touch the 

LOAD

 button and wait about 90 seconds for the slide valve to fully load. Smaller machines may

not require the full 90 seconds to load.

•

This process must be completed quickly because the indicator will abandon the calibration after a period
of time. Please note the red LED will flash approximately ¼ second every 5 seconds indicating the indi-
cator is active and that the calibration has not been fully completed.

12. Once the compressor is fully loaded, push the calibration button twice, and the red LED will flash rapidly for

approximately 3 seconds. Do not attempt to move slide valve until red LED turns 

Off

. When the red LED

stops flashing the loaded position is set.

13. At this time the sensor will have an output of 20 mA. This can be verified on the 

Operating Data

 screen.

14.

UNLOAD

 and 

LOAD

 the machine to confirm calibration. Refer to the 

Compressor Capacity

 on the 

Operating

Data

 screen. It should track the slide valve between 4 mA and 20 mA.

15. Stop the compressor by touching 

STOP

.

16. Reinstall the cover.

17. If the transducer was rotated, restore it to the original orientation and tighten the setscrews.

18. Return load/unload needle valves to their original positions to ensure proper slide valve movement.

Sensor Calibration
 

Instruction Manual | GEA Omni™

Control panel

234

GEA Refrigeration North America, Inc. | E_806550_2 | Generated 12.01.2016

Содержание Omni















































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды