GEA Omni Скачать руководство пользователя | Manualshive

Страница: 110 / 238

background image

Parameter

Units

Minimum

Maximum

Default

Control Mode After Shutdown

Selection – See Description

Sequencer Control

Selection – See Description

1.

Control Mode

This parameter is used to select which set of

Capacity Control

parameters is used by the panel. Whichever

set of parameters is selected here will be the visible set shown in the

Capacity Control

section above. This

parameter will only be visible if

Control Mode Select By Digital Input

is set to

Disabled

. The options are:

•

Capacity Control 1

•

Capacity Control 2

•

Capacity Control 3

2.

Control Mode Select By Digital Input

This parameter is used to select whether the capacity control mode is selected using a parameter or a Digital
Input point. If a Digital Input point is used, the compressor will be limited to Capacity Control 1 on a de-ener-
gized signal, and Capacity Control 2 on an energized signal. The parameter will only be visible if the

Set

Point Selection Digital Input

option is enabled in the panel configuration. The options are:

•

Enabled

•

Disabled

3.

Set Point Location

This parameter is used to select whether the capacity control set point is taken from the selected set of

Capacity Control

parameters or from a

Remote

device. The options are:

•

Local

•

Remote

4.

Remote Set Point Units

This parameter is used to select the units of measurement that will be used for remote set point control. The
parameter will only be visible if the

Remote Set Point

option is enabled in the panel configuration. The

options are:

•

Pressure

•

Temperature

•

Slide Valve

Control
Compressor Control Parameters

Instruction Manual | GEA Omni™

Control panel

110

GEA Refrigeration North America, Inc. | E_806550_2 | Generated 12.01.2016

«
...
108
109
110
111
112
...
»

Содержание Omni















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Omni

Бренд: NCR Страницы: 6

Smart-MPPT Li Series

Бренд: Y-Solar Страницы: 6

Бренд: Panasonic Страницы: 27

Бренд: Panasonic Страницы: 78

Бренд: Panasonic Страницы: 98

Бренд: NAiS Страницы: 173

Бренд: Panasonic Страницы: 2

Бренд: Harpo Страницы: 35

Бренд: Hardi Страницы: 2

Бренд: Rachio Страницы: 2

Бренд: VAT Страницы: 26

Бренд: Water Specialist Страницы: 60

Бренд: L-Acoustics Страницы: 20

Бренд: Vaillant Страницы: 12

Бренд: Madison AV Страницы: 2

Бренд: Bardiani Страницы: 96

Бренд: Eaton Страницы: 4

Бренд: M-system Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды