Keysight Technologies D9020DDRC Manual Download Page 83

Page: 83 / 370

DDR2(+LP) Compliance Testing Methods of Implementation

Single-Ended Signals AC Input Parameters Tests

PASS Condition

The high level voltage of DQS shall be greater than or equal to the minimum V

IH(DC)

value.

Measurement Algorithm

1 Acquire and split read and write burst of the acquired signal. (See notes on DDR read/write

separation).

2 Take the first valid WRITE burst found.
3 Find all valid Strobe positive pulse in the said burst. A valid Strobe positive pulse starts at V

ref

crossing at valid Strobe rising edge (See notes on threshold) and end at V

ref

crossing at following

valid Strobe falling edge (See notes on threshold).

4 For valid Strobe positive pulse #1, zoom on the pulse so that it appears on oscilloscope main

screen and perform V

TOP

measurement. Take result from V

TOP

measurement as V

IH(DC)

value.

5 Continue previous step with the rest of found valid Strobe positive pulse in the said burst.
6 Determine the worst result from the set of V

IH(DC)

measured.

Summary of Contents for D9020DDRC



















































































































































































































































































































































































Search results

Summary of Contents for D9020DDRC

Reviews:

Related manuals for D9020DDRC

Brands by name

Popular brands

Keysight Technologies D9020DDRC, Manual

Search results

Summary of Contents for D9020DDRC

Reviews:

Related manuals for D9020DDRC

Brands by name

Popular brands