Keysight Technologies D9020DDRC Manual Download Page 112 | Manualshive

Page: 112 / 370

background image

4

Single-Ended Signals AC Input Parameters Tests

96

DDR2(+LP) Compliance Testing Methods of Implementation

V

OH(DC)

- Test Method of Implementation

V

OH(DC)

- Single-ended DC Output Logic High Voltage.

The purpose of this test is to verify that the high level voltage value of the test signal within a valid
sampling window must be within the conformance limit of the V

OH(DC)

value as specified in the

JEDEC specification.

The value of V

DDQ

(which directly affects the conformance limit) is set to 1.2V for the compliance

limit set used. You may choose to use the User Defined Limit feature in the application to perform
this test against a customized test limit set based on different values of V

DDQ

.

Signals of Interest

Mode Supported: LPDDR2 only

Signal cycle of interest: READ

Signal(s) of Interest:
• Data Signal (supported by Data Strobe Signal) OR
• Data Strobe Signal (supported by Data Signal)

Signals required to perform the test on the oscilloscope:
• Pin Under Test, PUT - any signal of interest, as defined above
• Supporting Pin

Test Definition Notes from the Specification

Test References

See Table 82 - Single-ended AC and DC Output Levels in the

JESD209-2B

.

PASS Condition

The worst measured V

OH(DC)

shall be within the specification limit.

Measurement Algorithm

1 Acquire and split read and write bursts of the acquired signal.
2 Take the first valid READ burst found.
3 Find all valid signal positive pulses in this burst. A valid signal positive pulse starts at the V

REF

crossing on a valid signal rising edge and ends at the V

REF

crossing on the following valid signal

falling edge.

4 For the first valid positive pulse, zoom in on the pulse so that it appears on the oscilloscope’s

display and perform the V

TOP

measurement. Take the V

TOP

measurement result as the V

OH(DC)

value.

5 Continue the previous step for the rest of the valid signal positive pulses that were found in the

burst.

6 Determine the worst result from the set of V

OH(DC)

measured.

Table 64

LPDDR2 Single-ended AC and DC Output Levels

Symbol

Parameter

LPDDR2-1066 to LPDDR2-200

Units

Notes

V

OH(DC)

DC output high measurement level (for IV curve linearity)

0.9 x V

DDQ

V

1

«
...
110
111
112
113
114
...
»

Summary of Contents for D9020DDRC



















































































































































































































































































































































































Reviews:

No comments

Related manuals for D9020DDRC

Brand: Eastern Jungle Gym Pages: 17

Brand: Vahle Pages: 96

Brand: E-Z DRILL Pages: 12

Brand: e-survey Pages: 54

Brand: E-Pill Pages: 8

XL-7 Command Station

Brand: E-Mu Pages: 22

BOMAG BW 100 ADM-5

Brand: Fayat Pages: 216

Brand: B medical systems Pages: 28

Brand: Gardigo Pages: 24

Brand: Gardner Bender Pages: 8

Brand: Garantia Pages: 4

Brand: NARIKA Pages: 2

Brand: Labelmate Pages: 61

Brand: Labconco Pages: 62

ThermoTweez Handpiece TT-65

Brand: Pace Pages: 14

Brand: R&S Pages: 2677

Brand: YASKAWA Pages: 81

Brand: YASKAWA Pages: 52

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands