Keysight Technologies D9020DDRC Manual Download Page 105

Page: 105 / 370

DDR2(+LP) Compliance Testing Methods of Implementation

Single-Ended Signals AC Input Parameters Tests

Test References

See Table 21 - AC Input Test Conditions in the

JEDEC Standard JESD79-2E

and Table 21 - AC Input

Test Conditions in the

JESD208

PASS Condition

The calculated Falling Slew value for the test signal should be greater than or equal to the SLEW
value.

Measurement Algorithm

1 Acquire the signal.
2 Find all valid falling edges in the whole acquisition. A valid falling edge starts at V

IH(AC)

crossing

and ends at the following V

IL(AC)

crossing.

3 For all valid rising edges, find the transition time, delta TR, which is the time starting at V

REF

crossing and ending at the following V

IL(AC)

crossing.

4 Calculate the Falling Slew:

5 Determine the worst result from the set of Slew

measured.

FallingSlew

REF

–

IL AC





max



------------------------------------

Summary of Contents for D9020DDRC



















































































































































































































































































































































































Search results

Summary of Contents for D9020DDRC

Reviews:

Related manuals for D9020DDRC

Brands by name

Popular brands

Keysight Technologies D9020DDRC, Manual

Search results

Summary of Contents for D9020DDRC

Reviews:

Related manuals for D9020DDRC

Brands by name

Popular brands