Keithley 4200A-SCS Reference Manual Download | Manualshive

Page: 184 / 1381

background image

Model 4200A-SCS Parameter Analyzer Reference Manual

Section 4: Multi-frequency capacitance-voltage unit

4200A-901-01 Rev. C / February 2017

4-91

Formula: INV_C

Formula name: INV_C (C)

Units: 1/F

Description: Inverse capacitance.

Formulator entry: INV_C = 1/(CP_AC)^2

Simplified equation:

Formula: DOPING

Formula name: DOPING (N)

Units: 1/cm

3

Description: Majority carrier concentration.

Formulator entry:

DOPING = ABS(2/Q/ES/AREA^2/DIFF(INV_C, DCV_AC))

Simplified equation:

Constants for the diode project

Constant

Default Value

Units

Description

AREA

0.0001

cm

2

Gate area of device

ES

1.034e-12

F/cm

ε

S

- Semiconductor permittivity

cvsweep-diode test

This test measures the PN junction capacitance as a function of the DC bias voltage while the
junction is reverse biased. The test makes a capacitance measurement at each step of a user-
configured linear voltage sweep. From the acquired C-V data, the test uses the Formulator to
calculate parameters.

cvsweep-diode Analyze sheet

The test data is displayed in the Analyze sheet:

•

Cp_AC: Measured parallel capacitance.

•

Gp_AC: Measured conductance.

•

DCV_AC: Forced DC bias voltage.

•

F_AC: Forced test frequency.

•

Formulas: Formulator calculation results.

AC = Anode to cathode

«
...
182
183
184
185
186
...
»

Summary of Contents for 4200A-SCS






































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 4200A-SCS

Brand: ICM Controls Pages: 8

Brand: National Instruments Pages: 85

Brand: National Instruments Pages: 12

Brand: National Instruments Pages: 18

Brand: National Instruments Pages: 12

Brand: Oceanic Pages: 68

Brand: Oceanic Pages: 24

Brand: Tavool Pages: 12

Brand: Gearx Pages: 19

Brand: Flowmetrics Pages: 102

Brand: RIDGID Pages: 18

Brand: Gates Pages: 112

Brand: OHAUS Pages: 84

Brand: Bruker BioSpin Pages: 76

WTW SensoLyt 900

Brand: Xylem Pages: 12

Brand: Vanguard Instruments Pages: 85

Brand: Benetech Pages: 16

Brand: Avtech Pages: 40

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands