manualshive.com logo in svg

IDT PCI Express 89HPES32NT24xG2, User Manual, Page: 488 / 744

Share
Download
IDT PCI Express 89HPES32NT24xG2 User Manual Download Page 488

IDT   Proprietary Port Specific Registers

PES32NT24xG2 User Manual

21 - 40

January 30, 2013

Notes

NTMCOVR[3:0]BARL - NT Multicast Overlay x Base Address Low

NTMCOVR[3:0]BARH - NT Multicast Overlay x Base Address High

AER Error Emulation

P2PUEEM - PCI-to-PCI Bridge Uncorrectable Error Emulation (0xD90)

Bit 

Field

Field

Name

Type Default

Value

Description

5:0

OVRSIZE

RW

0x0

Overlay Size.
This field specifies the size in bytes of the overlay aperture 
as a power of 2.
The value in this field must be programmed to six or above. 
When the value in this field is less than six, the operation is 
undefined.
Refer to section Non-Transparent Multicast Operation on 
page 17-6 for details on programming this field.

31:6

MCBARL

RW

0x0

Multicast Overlay BAR Low.
This field specifies the lower 24-bits (i.e., bits 6 through 31) 
of the NT multicast overlay base address.
Refer to section Non-Transparent Multicast Operation on 
page 17-6 for details on programming this field.

Bit 

Field

Field

Name

Type Default

Value

Description

31:0

MCBARH

RW

0x0

Multicast Overlay BAR High.
This field specifies the upper 32-bits (i.e., bits 32 through 
63) of the NT multicast overlay base address.
Refer to section Non-Transparent Multicast Operation on 
page 17-6 for details on programming this field.

Bit 

Field

Field

Name

Type Default

Value

Description

3:0

Reserved

RO

0x0

Reserved field.

4

DLPERR

RW

0x0

SWSticky

Data Link Protocol Error Trigger. 
Writing a one to this bit causes the corresponding error bit 
to get set in the PCI-to-PCI Bridge function’s AERUES reg-
ister. This bit always returns 0x0 when read.

5

SDOENERR

RW

0x0

SWSticky

Surprise Down Error Trigger. 
Writing a one to this bit causes the corresponding error bit 
to get set in the PCI-to-PCI Bridge function’s AERUES reg-
ister. This bit always returns 0x0 when read.

11:6

Reserved

RO

0x0

Reserved field.

12

POISONED

RW

0x0

SWSticky

Poisoned TLP Trigger. 
Writing a one to this bit causes the corresponding error bit 
to get set in the PCI-to-PCI Bridge function’s AERUES reg-
ister. This bit always returns 0x0 when read.

Summary of Contents for PCI Express 89HPES32NT24xG2









































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments