manualshive.com logo in svg

IDT PCI Express 89HPES32NT24xG2, User Manual, Page: 422 / 744

Share
Download
IDT PCI Express 89HPES32NT24xG2 User Manual Download Page 422

IDT   PCI-to-PCI Bridge Registers

PES32NT24xG2 User Manual

20 - 38

January 30, 2013

Notes

Message Signaled Interrupt Capability Structure

MSICAP - Message Signaled Interrupt Capability and Control (0x0D0)

MSIADDR - Message Signaled Interrupt Address (0x0D4)

Bit 

Field

Field

Name

Type Default

Value

Description

7:0

CAPID

RO

0x5

Capability ID. 
The value of 0x5 identifies this capability as a MSI capabil-
ity structure.

15:8

NXTPTR

RWL

HWINIT

(See 

description)
MSWSticky

Next Pointer. 
This field contains a pointer to the next capability structure. 
This field is set to 0x0 indicating that it is the last capability.
The default value of this register depends on the port’s 
operating mode. See section PCI-to-PCI Bridge Capability 
Structures on page 19-9 for details.
Note that this field is MSWSticky. Therefore, if this field is 
modified by software, its value will be preserved regardless 
of any port operating mode change.

16

EN

RW

0x0

Enable. 
This bit enables MSI.
0x0 - (disable) disabled

0x1 - (enable) enabled

19:17

MMC

RO

0x0

Multiple Message Capable. 
This field contains the number of requested messages.

22:20

MME

RW

0x0

Multiple Message Enable. 
Hardwired to one message.

23

A64

RO

0x1

64-bit Address Capable. 
The bridge is capable of generating messages using a 64-
bit address.

31:24

Reserved

RO

0x0

Reserved field.

Bit 

Field

Field

Name

Type Default

Value

Description

1:0

Reserved

RO

0x0

Reserved field.

31:2

ADDR

RW

0x0

Message Address. 
This field specifies the lower portion of the DWORD 
address of the MSI memory write transaction. 
Refer to section Interrupts on page 10-4 for restrictions on 
the programming of this field.

Summary of Contents for PCI Express 89HPES32NT24xG2









































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments