manualshive.com logo in svg

IDT PCI Express 89HPES32NT24xG2, User Manual, Page: 428 / 744

Share
Download
IDT PCI Express 89HPES32NT24xG2 User Manual Download Page 428

IDT   PCI-to-PCI Bridge Registers

PES32NT24xG2 User Manual

20 - 44

January 30, 2013

Notes

13

FCPERR

RO

0x0

Flow Control Protocol Error Mask. 
Not applicable.

14

COMPTO

RO

0x0

Completion Timeout Mask. 
Not applicable.

15

CABORT

RO

0x0

Completer Abort Mask. 
Not applicable.

16

UECOMP

RW

0x0

Sticky

Unexpected Completion Mask. 
When this bit is set, the corresponding bit in the AERUES 
register is masked. When a bit is masked in the AERUES 
register, the corresponding event is not logged in the 
advanced capability structure, the First Error Pointer field 
(FEPTR) in the AERCTL register is not updated, and an 
error is not reported to the root complex.
This bit does not affect the state of the corresponding bit in 
the AERUES register.

17

RCVOVR

RW

0x0

Sticky

Receiver Overflow Mask. 
When this bit is set, the corresponding bit in the AERUES 
register is masked. When a bit is masked in the AERUES 
register, the corresponding event is not logged in the 
advanced capability structure, the First Error Pointer field 
(FEPTR) in the AERCTL register is not updated, and an 
error is not reported to the root complex.
This bit does not affect the state of the corresponding bit in 
the AERUES register.

18

MALFORMED

RW

0x0

Sticky

Malformed TLP Mask. 
When this bit is set, the corresponding bit in the AERUES 
register is masked. When a bit is masked in the AERUES 
register, the corresponding event is not logged in the 
advanced capability structure, the First Error Pointer field 
(FEPTR) in the AERCTL register is not updated, and an 
error is not reported to the root complex.
This bit does not affect the state of the corresponding bit in 
the AERUES register.

19

ECRC

RW

0x0

Sticky

ECRC Mask. 
When this bit is set, the corresponding bit in the AERUES 
register is masked. When a bit is masked in the AERUES 
register, the corresponding event is not logged in the 
advanced capability structure, the First Error Pointer field 
(FEPTR) in the AERCTL register is not updated, and an 
error is not reported to the root complex.
This bit does not affect the state of the corresponding bit in 
the AERUES register.

20

UR

RW

0x0

Sticky

UR Mask. 
When this bit is set, the corresponding bit in the AERUES 
register is masked. When a bit is masked in the AERUES 
register, the corresponding event is not logged in the 
advanced capability structure, the First Error Pointer field 
(FEPTR) in the AERCTL register is not updated, and an 
error is not reported to the root complex.
This bit does not affect the state of the corresponding bit in 
the AERUES register.

Bit 

Field

Field

Name

Type Default

Value

Description

Summary of Contents for PCI Express 89HPES32NT24xG2









































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments