Festo CMMT-ST-SW Скачать руководство пользователя | Manualshive

Страница: 30 / 616

background image

3. Define device name.

The length of the device name is limited by the following rules:
•

The device name must not exceed 126 characters.

•

Umlauts (ä, ö, ü) and special characters (e.g. ß, @) are counted as two characters.

4. Actuate "Apply" button.

Ä

The device may need to be restarted in some cases.

5.

NOTICE!

Unpredictable behaviour of the machine when the device is restarted.

Depending on the device, a restart (reboot) may be required to complete the following functions.
A safety note is displayed before the restart.
•

Only acknowledge the safety note once you have ensured that any unpredictable or unexpec-
ted behaviour of the connected machine cannot cause any damage.

Ensure that any unpredictable behaviour by the device cannot cause any damage. Confirm mes-
sage with "Ok".

Ä

The device name is changed.

Defining network settings

The network settings for the device can be defined via the device communication dialogue.
Requirements:
–

The device communication dialogue is open.

–

Devices were found in the network.

1. Click on the required device with the right mouse button.
2. Select "Change _Network Settings".

Ä

The current network settings are displayed.

3. Change network settings as required.

The network settings can vary depending on the specific device.

–

"DHCP" activated: The dynamic assignment of the IP address is activated. This is only per-
missible if a DHCP server is available in the network. If DHCP is activated, the following set-
tings (subnet mask, gateway and DNS) are greyed out.

–

"DHCP" deactivated: The network settings implemented in the following lines are applied.

4. Actuate "Apply" button.

Ä

The device may need to be restarted in some cases.

CMMT-ST Plug-in

30

Festo — CMMT-ST-SW — 2019-02

«
...
28
29
30
31
32
...
»

Содержание CMMT-ST-SW









































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CMMT-ST-SW

Бренд: INVT Страницы: 125

Бренд: Danfoss Страницы: 161

Бренд: YASKAWA Страницы: 196

Бренд: elero Страницы: 31

Бренд: BTC Страницы: 22

Бренд: LaCie Страницы: 32

Бренд: CHINSC ELECTRIC Страницы: 169

DVR 115D - DVD±RW Drive - IDE

Бренд: Pioneer Страницы: 2

DVR 116D - DVD±RW Drive - IDE

Бренд: Pioneer Страницы: 4

DVR 115D - DVD±RW Drive - IDE

Бренд: Pioneer Страницы: 5

Бренд: Pioneer Страницы: 1

Бренд: Pioneer Страницы: 5

Бренд: Pioneer Страницы: 8

Бренд: Pioneer Страницы: 8

Бренд: Pioneer Страницы: 8

BDC-2202 - DVD±RW / DVD-RAM

Бренд: Pioneer Страницы: 2

Бренд: Pioneer Страницы: 17

215D - DVR - Disk Drive

Бренд: Pioneer Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды