Xerox WorkCentre 5790 Series, Service Manual, Page: 1481 / 1610

May 2013
6-97 Xerox® WorkCentre® 5790 Family
dC131a
General Procedures/Information
09-319 ROS Laser Adj
Nom Used to display the ROS
laser light level adjusted
nominal.
06-001 must be set to the
same value as 09-319. 750 to 9000 35 ppm=3471
40-55 ppm
=2250,
65-75 ppm
=2400
09-320 ROS Laser Adj
Enable Used to enable ROS laser
light level nominal adjust-
ment. 0=disabled
1=enabled 1
09-321 IQA Grid V Offset IQA Grid V Offset level.
Unsigned no. in NVM table
(displayed on GUI) to be
converted to signed no.
over range of -40 to +40
(Volts) by subtraction of 40
from table value. 0 to 80 40
09-322 IQA ROS Level
Offset IQA ROS Level Offset level.
Unsigned no. in NVM table
(displayed on GUI) to be
converted to signed no.
over range of -1500 to
+1500 (mErg/cm2) by sub-
traction of 1500 from table
value. 0 to 3000 1500
09-331 Upper Relaxation Upper relaxation capping
limit when aggressive dis-
pense mode active. 100 to 600% 400
09-332 Prop B Factor Additional factor applied to
the proportional term when
aggressive dispense mode
active. 100 to 1000% 100
09-400 XRU Blade A Coefficient A. 0 to 10000ug/s 35 ppm=200
40-55 ppm
=350,
65-90 ppm
=500
09-401 XRU Blade B Coefficient B. 0 to 1000ug per
10^5 pixels 16
09-402 XRU Blade Mco Blade maintenance level at
cycle out. 0 to 3000mg 0
09-403 XRU Blade CICO
bands Prediction of blade mainte-
nance provided by cycle in
and cycle out bands. 0 to 100mg 35 ppm=8
40-55 ppm =9
65-90 ppm =11
09-404 XRU Blade
Level(1) XRU Blade maintenance
threshold level 1. 2 to 3000mg 10
09-405 XRU Blade
Level(2) XRU Blade maintenance
threshold level 2. 1 to 3000mg 30
Table 8 NVM chain 9
Location NVM Name NVM Description Value Default
09-406 XRU Blade
Count(1) XRU Blade maintenance
event type 1 counter. 0 to 3000 0
09-407 XRU Blade
Count(2) XRU Blade maintenance
event type 2 counter. 0 to 3000 0
09-408 XRU Blade C Coefficient C. 0 to 10000ug
per 10^5 pixels 805
09-409 XRU Blade Enable XRU Blade maintenance
enable/disable.
0=disable (XT)
1=enable (EA) 0 for XT,
1 for EA
09-410 XRU Blade
ML(max) XRU Blade maintenance
level maximum level. 0 to 300ug 42
Table 9 NVM chain 10
Location NVM Name NVM Description Value Default
10-028 Standby Temp Target temperature during
standby mode. 10 to 218
degrees C 35 ppm=190
40-55 ppm
=195,
65-90 ppm
=208
10-029 Run Temp Target temperature during
run mode. 100 to 213
degrees C 35 ppm=185
40-55 ppm
=195,
65-90 ppm
=203
10-030 Low Power Temp Target temp during Power
save mode. The low power
simmer temperature is deter-
mined by the Power Save
mode set in Tools. 50 to 150
degrees C 35 ppm=85
40-55 ppm
=95,
65-90 ppm
=135
10-042 101-120 mm offset Offset temperature required
on thermistor B for paper
width. Unsigned number in
NVM table (displayed on
GUI) to be converted to
signed number. by subtrac-
tion of 10 from table value.
i.e. 8 displayed in NVM is
equivalent to -2 degrees Cel-
sius
0 to 20 10
Table 8 NVM chain 9
Location NVM Name NVM Description Value Default