Xerox WorkCentre 5790 Series, Service Manual

Page: 1473 / 1610

May 2013
6-89 Xerox® WorkCentre® 5790 Family
dC131a
General Procedures/Information
08-289 Fsr Step Temperature difference
between 2 consecutive
readings. 0 to 0 deg. C 3
08-290 Fsr TolrunB Temperature tolerance
either side of run target tem-
perature. Thermistor B. 0 to 0 deg. C 35-45 ppm=0
55-90 ppm=40
08-291 Fsr Max1 Temperature at which soft-
ware calls an over tempera-
ture fault. 0 to 0 deg. C 230
08-292 Fsr Max2 Temperature at which the
electronics shutdown the
fuser. 0 to 0 deg. C 245
08-293 Fsr Tolstandby Temperature tolerance
either side of standby target
temperature. 0 to 0 deg. C 35 ppm=26
40-55 ppm=20
65-90 ppm =15
08-294 Fsr Apply Power
Time Fuser apply power time. 100 to
20000ms 200
08-295 Fsr Bias To Run
Time Fuser bias to marking mode
time. 0 to 0 deg. C 0
08-296 Trange Cooling Temperature offset above T
save at which control and
fault detection is enabled. 0 to 0 deg. C 10
08-297 Inv Mot On Fwd Time from LE at inverter
sensor to inverter motor on
forward. 200 to
20000ms 35 ppm=860
40-55 ppm
=600,
65-90 ppm
=330
08-298 LE Inv Snr Mot On
Frwd Dup Time to turn on inverter
motor on after LE leaves
fuser (duplex). 300 to 1000ms 35 ppm=860
40-55 ppm
=600,
65-90 ppm
=330
08-299 TEF sr Exit Jam
Win Siz2 TE post fuser to exit jam
window. 400 to 1700ms 35 ppm=1490
40-55 ppm
=1060,
65-75 ppm
=640
08-300 TE Inv Snr To Inv
Path Sol Actuates inverter path sole-
noid to divert duplex sheet
to output from TE of previ-
ous sheet at inverter sen-
sor. 0 to 100 steps 35-55 ppm=30
65-90 ppm =40
Table 7 NVM chain 8
Location NVM Name NVM Description Value Default
08-301 TE Snr To Inv Sol
On Exit Actuates inverter path sole-
noid to divert duplex sheet
to output from TE of previ-
ous sheet when registration
clutch turns on. 500 to 800
steps 35-55 ppm
=628,
65-90 ppm
=620
08-302 TE Inv Snr To Inv
Sol Off Disables inverter path sole-
noid to divert sheet into
invert path after TE at
inverter sensor. 0 to 100 steps 35-45 ppm=0
55-90 ppm=40
08-303 TE Inv Snr To Mot
Of Smp S2 Inverter motor off stop posi-
tion (simplex). 0 to 400 steps 35-55 ppm=40
65-90 ppm =58
08-304 TE Inv Snr To Mot
Of Dup S2 Time to turn off inverter
motor after TE leaves
inverter sensor (duplex). 0 to 400ms 35-55 ppm=97
65-90 ppm =90
08-305 TE Pst Fsr Exit
Jam Win S2 Number of steps from TE
post fuser to exit jam win-
dow. 400 to 1700 35-55 ppm
=640,
65-75 ppm
=760
08-306 LE Lt Inv Frm LE
Pst Fsr Number of steps from LE at
post fuser to LE at inverter
sensor. 0 to 300 35-55 ppm
=130,
65-90 ppm
=170
08-307 Tri Rol Open Frm
Fsr Snr Number of steps before the
tri roll split nip opens after
TE at fuser exit switch. 0 to 200 0
08-308 Tri Rol Close Frm
Inv Off Number of steps before the
tri roll split nip closes after
inverter motor off (forward). 0 to 200 35-55 ppm =0
65-90 ppm =30
08-309 Tim To Del Invert IOT time to deliver. 800 to 2000
steps 35-55 ppm
=1678,
65-90 ppm
=1553
08-310 TE Late Frm Inv
Sensor Jam window for TE late
from inverter sensor. 0 to 300 steps 35 ppm=168
40-55 ppm
=117,
65-90 ppm =83
08-311 Top Edge Reg T5
Dup Tray 5 top edge registration
duplex. 7300 to 7700 7510
08-312 T5 Feed Head
Count Tray 5 nudger roll, feed roll
and retard roll feed count. 0 to 1500000 0
08-313 Tray 5 Configura-
tion 0 = Tray 5 Standard: A4
LEF, 8.5x11 LEF
1 = Tray 5 Kit A: A3 SEF,
11x17 SEF
2 = Tray 5 Kit B: A4 SEF,
8.5x11 SEF, 8.5x14 SEF 0 to 2 0
Table 7 NVM chain 8
Location NVM Name NVM Description Value Default