Xerox WorkCentre 5790 Series, Service Manual

Page: 1464 / 1610

May 2013
6-80 Xerox® WorkCentre® 5790 Family
dC131a
General Procedures/Information
07-010 LE Late T2 Feed
Snr Maximum number of steps
from tray 2 feed motor to LE
at tray 2 feed sensor. 0 to 500 200
07-011 T1 Buckle Size Number of steps from LE at
tray 1 feed sensor to start of
transport motor. 0 to 200 13
07-012 T2 Buckle Size Number of steps from LE at
tray 2 feed sensor to start of
tray 1 and 2 transport motor. 0 to 200 13
07-013 LE Late T1 From T2 Maximum number of steps
from tray 2 TAR nips to LE at
tray 1 feed sensor.
0 to 1200 940
07-014 LE Late Wait Point
T1-T2 Maximum number of steps
from tray 1 TAR nips to LE at
wait sensor. 0 to 1400 1000
07-015 Wait Point Steps T1-
T4 Number of steps from LE at
wait sensor to tray 1 and 2
transport motor stop. 0 to 600 35-55 ppm
=240,
65-90 ppm
=434
07-016 Release Steps T1-
T4 Number of steps the tray 1
and 2 transport motor should
run after the release sheet
command. 0 to 2000 440
07-017 LE Late T2 From
T3-T4 Time for the LE of an HCF
sheet to reach the tray 2 feed
sensor. 0 to 2000 35-55 ppm =
1400, 65-90
ppm = 1950
07-018 Release Steps T5 Distance from wait point to
transport motor releasing
sheet. 0 to 1000 116
07-019 T3 Stack Height
Adjust Number of steps tray 3 has to
be lifted above the stack
height sensor for optimum
feed position. 0 to 100 50
07-020 T4 Stack Height
Adjust Number of steps tray 4 has to
be lifted above the stack
height sensor for optimum
feed position. 0 to 100 50
07-021 LE Late T3 Feed
Snr Maximum number of steps
from tray 3 feed motor to LE
at tray 3 feed sensor. 0 to 700 350
07-022 LE Late T4 Feed
Snr Maximum number of steps
from tray 4 feed motor to LE
at tray 4 feed sensor. 0 to 800 400
07-023 T3 Buckle Size Size of de-skew buckle. 0 to 15 3
07-024 T4 Buckle Size Size of de-skew buckle. 0 to 15 10
Table 6 NVM chain 7
Location NVM Name NVM Description Value Default
07-025 Release Steps T3-
T4 Number of steps the HCF
transport motor should run
after the release sheet com-
mand. 0 to 15 5
07-026 LE Late T4 From T3 Maximum number of steps
from tray 3 TAR nips to LE at
tray 4 feed sensor.
0 to 2000 1000
07-027 Wait Point Steps T3-
T4 Number of steps from tray 4
feed sensor to stop position. 30 to 100 35-55 ppm =4
0,
65-90 ppm =
53
07-028 PreRelease Dis-
tance T1 Number of steps for pre-
sheet separation. 100 to 150 130
07-029 Tray Media Combi
Switch Tray media size sensing
switch to alternate between
old and new switch combina-
tions. 0=Old
combination1
=New combi-
nation 1
07-032 FeedCL4AcqDelayT
ime HCF (W/ TAG 151 ) Delay
before feed clutch is enabled
to acquire a sheet
0 to 6000ms 35 ppm =
400, 40-45
ppm =250, 55
ppm = 50, 65
ppm = 100,
75 ppm = 60,
90 ppm = 0
07-033 HCFWaitPoint4Step
s HCF (W/ TAG 151 ) Number of
HCF tray 4 motor steps from
HCF exit sensor to the HCF
wait point
0 to 2000 35 ppm =
180, 40-55
ppm =140,
65-75 ppm =
200, 90 ppm
= 230
07-034 T4ExSenClutchOffS
tps HCF (W/ TAG 151 ) Number of
steps of the tray 4 feed motor
from the LE at HCF exit sen-
sor to tray 4 feed clutch de-
energised
0 to 1000 342
07-035 T4RampSteps HCF (W/ TAG 151 ) Number of
steps in the tray 4 feed motor
ramp from/to 525mm/sec.
Used to correct clutch de-
energise time.
0 to 500 54
07-036 T4WaitPtRelDelTim
e HCF (W/ TAG 151 ) Minimum
delay time from PFM release
sheet (sheet ahead) to sheet
being released from HCF
wait point.
0 to 500ms 35-45 ppm =
250, 55 ppm
=150, 65-75
ppm = 110,
90 ppm = 80
Table 6 NVM chain 7
Location NVM Name NVM Description Value Default