Xerox WorkCentre 5790 Series, Service Manual

Page: 1463 / 1610

May 2013
6-79 Xerox® WorkCentre® 5790 Family
dC131a
General Procedures/Information
03-425 PhotoModeTR-
COffset TRC offset in photo mode 0 to 500 400
03-426 CustomMedi-
aEnable Custom display names for
custom media types - fea-
ture enablement 0 = Disable
1 = Enabled 0
03-427 CustomMediaL-
istInit Custom display names -
Custom media type List
Initialized flag 0 = Disable
1 = Enabled 0
03-900 Restrict Diag.
Pin Retains the restricted diag-
nostics pin. Use with 08-
900 1000 to 99999999 1962
Table 4 NVM chain 5
Location NVM Name NVM Description Value Default
05-001 DADH Feed Head
Count Number of feeds. 0 to 300000 0
05-002 CRU Days Number of days. 0 to 65535 0
05-007 Detect Paper Size 1 DADH sensor to detect sizes
for market regions.
0=A4,
1=8.5x13,
2=Auto market
region set 2
05-008 Detect Paper Size 2 DADH sensor to detect sizes
for market regions.
0=A5;
1=8.5x5.5,
2=auto market
region set 2
05-009 DADH Mag (copy
mode) Half speed adj for >100%
copy. 0 to 200
minus 10% to
plus 10% 35-55 ppm
=100,
65-90 ppm
=94
05-012 DADH Duplex Motor
Speed Adjustment of duplex motor
speed. 0=normal
1=quiet mode
(reduced
speed) 0
Table 5 NVM chain 6
Location NVM Name NVM Description Value Default
06-001 Laser Light Level ROS light level 600 dpi and
1200 dpi.
09-319 must be set to the
same value as 06-001. 1500 to 6000 35ppm
=3471,
40-55 ppm
=2250,
65-90 ppm
=2400
06-003 Ros Motor Time-out Time after which ROS motor
fault will be called.
100 to
20000ms 5000
Table 3 NVM chain 3
Location NVM Name NVM Description Value Default
06-005 Extended Rng Ros
Enable Indicates which type of ROS
is fitted (35 ppm only). 0 = 3 to 6 Erg/
cm2 range
ROS
1 = 1.5 to 6
Erg/cm2
Extended
range ROS 1
Table 6 NVM chain 7
Location NVM Name NVM Description Value Default
07-001 Feeder Module Type Defines feeder module type
67=2 internal trays + bypass
68=2 internal trays + bypass
+ HCF
177=2 internal trays + bypass
+ tray 5180=2 internal trays +
HCF + tray 5
67 to 180 67
07-002 LE Late T5 Feed
Snr Steps allowed before a sheet
is declared a misfed. LE late
to tray 5 feed sensor. 0 to 800 500
07-003 LE Late Wait Point
T5 Number of transport motor
steps allowed between the
LE at TAR nips to hand over
before a jam is declared. 0 to 2000 35-55 ppm
=1052,
65-90 ppm
=724
07-004 Wait Point Steps T5 Number of transport motor
steps from the time the LE is
at pre hand over to hand over
point.
0 to 500 35-55
ppm=115,
65-90 ppm
=223
07-005 T1 Stock Level Number of steps tray 1 has
been lifted since it was last
closed. 0 to 700 0
07-006 T2 Stock Level Number of steps tray 2 has
been lifted since it was last
closed. 0 to 700 0
07-007 T1 Stack Height
Adjust Number of steps tray 1 has to
be lifted above the stack
height sensor for optimum
feed position. 0 to 40 7
07-008 T2 Stack Height
Adjust Number of steps tray 2 has to
be lifted above the stack
height sensor for optimum
feed position. 0 to 40 7
07-009 LE Late T1 Feed
Snr Maximum number of steps
from tray 1 feed motor to LE
at tray 1 feed sensor. 0 to 500 200
Table 5 NVM chain 6
Location NVM Name NVM Description Value Default