Siemens SINAMICS G120D CU240D-2 DP Page 350 Manual Download | Manualshive

Page: 350 / 980

background image

2 Parameters
2.2 List of parameters

SINAMICS G120D

350

List Manual (LH14), 01/2016, A5E33842313

Caution:

The STOP cams are low active.
Sets message 07492 as fault (F07492):
For a 0 signal, the axis is stopped with the OFF3 ramp-down time (p1135), status signal r2684.14 is set to 1, saved
and the appropriate fault is output. After the fault has been acknowledged, only motion moving away from the STOP
cam is permitted.
For a 0/1 signal and valid travel direction, when the STOP cam is exited, this is detected and the status signal
r2684.14 is set to 0.
Sets message 07492 as alarm (A07492):
For a 0 signal, the axis is stopped with the maximum deceleration (p2573), status signal r2684.14 is set to 1, saved
and the appropriate alarm is output. Only motion away from the STOP cam is permitted.
For a 0/1 signal and valid travel direction, when the STOP cam is exited, this is detected and the status signal
r2684.14 is set to 0 and the alarm is deleted.

Description:

Sets the maximum velocity for the "basic positioner" function (EPOS).

Dependency:

Refer to: r1084, r1087, p2503, p2504, p2505, p2506

Note:

The maximum velocity is active in all of the operating modes of the basic positioner.
The maximum velocity for the basic positioner should be aligned with the maximum speed/velocity of the
speed/velocity controller:
Rotary encoders:
p2571[1000 LU/min] = min(|r1084|, |r1087|)[rpm] x p2505/p2504 x p2506/1000
Linear encoders:
p2571[1000 LU/min] = min(|r1084|, |r1087|)[m/min] x p2503/10[m]

Description:

Sets the maximum acceleration for the "basic positioner" function (EPOS).

Dependency:

Refer to: p2619, p2644

Note:

The maximum acceleration appears to exhibit jumps (without jerk).
"Traversing blocks" operating mode:
The programmed acceleration override (p2619) acts on the maximum acceleration.
"Direct setpoint input/MDI" mode:
The acceleration override is effective (p2644, 4000 hex = 100 %).
"Jog" and "search for reference" modes
No acceleration override is active. The axis starts with the maximum acceleration.

Description:

Sets the maximum deceleration for the "basic positioner" function (EPOS).

Dependency:

Refer to: p2620, p2645

p2571

EPOS maximum velocity / v_max

CU250D-2_PN_F
CU250D-2_DP_F

Access level:

1

Calculated:

-

Data type:

Unsigned32

Can be changed:

U, T

Scaling:

-

Dyn. index:

-

Unit group:

-

Unit selection:

-

Func. diagram:

3630

Min Max

Factory

setting

1 [1000 LU/min]

40000000 [1000 LU/min]

30000 [1000 LU/min]

p2572

EPOS maximum acceleration / a_max

CU250D-2_PN_F
CU250D-2_DP_F

Access level:

1

Calculated:

-

Data type:

Unsigned32

Can be changed:

T

Scaling:

-

Dyn. index:

-

Unit group:

-

Unit selection:

-

Func. diagram:

3630

Min Max

Factory

setting

1 [1000 LU/s²]

2000000 [1000 LU/s²]

100 [1000 LU/s²]

p2573

EPOS maximum deceleration / -a_max

CU250D-2_PN_F
CU250D-2_DP_F

Access level:

1

Calculated:

-

Data type:

Unsigned32

Can be changed:

T

Scaling:

-

Dyn. index:

-

Unit group:

-

Unit selection:

-

Func. diagram:

3630

Min Max

Factory

setting

1 [1000 LU/s²]

2000000 [1000 LU/s²]

100 [1000 LU/s²]

«
...
348
349
350
351
352
...
»

Summary of Contents for SINAMICS G120D CU240D-2 DP





















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SINAMICS G120D CU240D-2 DP

Brand: GCAN Pages: 16

Brand: National Instruments Pages: 4

Brand: SunSynk Pages: 10

Brand: NAIM Pages: 22

Brand: Monoprice Pages: 2

MOAB30-09HFN8-QRD0GW

Brand: Midea Pages: 172

Brand: Balluff Pages: 2

Brand: AVT Pages: 82

Brand: Sincro Pages: 84

blueplanet 87.0 TL3

Brand: Kaco Pages: 115

Brand: ETQ Pages: 32

Brand: Woodpecker Pages: 22

Brand: Fairport Pages: 9

L-EM1000 series

Brand: Lacon Pages: 11

Brand: JDS Labs Pages: 5

Brand: M-system Pages: 2

Brand: TR-Electronic Pages: 32

CRS2F31-100 Series

Brand: Transition Networks Pages: 7

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands