manualshive.com logo in svg

Fuji Xerox Phaser 5500, Service Manual

Share
Download
Fuji Xerox Phaser 5500 Service Manual Download Page 92

3-14

Phaser 5500 Printer Service Manual

Messages, Codes, and Procedures

The error messages and codes generated by the printer’s operating system, the Service 
Usage Profile, and Service Diagnostics are the lead-in to the troubleshooting 
procedures that follow in subsequent pages. This section correlates the output of these 
three diagnostic aids and provides the troubleshooting procedure to locate and correct 
reported errors.

Error Message Abbreviations

Due to limited display space, some error messages include abbreviations. The most 
common abbreviations used throughout this chapter are listed here.

Error Message Abbreviations

Term

Definition

Comment

Reg or REGI

Registration

Used in designators such as Reg SNR.

SNR

Sensor

Often seen as SNR1 or Reg SNR.

DUP or DM

Duplex Unit

Optional for 2-sided printing.

F/O

Feed Out

Used as sensor designators F/O1 or F/O #2.

T/A

Take Away

Function designator for roller or motor.

H-Xport

Horizontal Transport

Horizontal Transport section of the Finisher.

MCU

Main Control Unit

Engine Logic Board

I/P Board

Image Processor

Image Processor Board

OCT

Offset Catch Tray

Offset Rollers at Exit

HCF

High-Capacity Feeder

Option Tray 6 or 2000-Sheet Feeder

MSI or MPT

Multi-Sheet Input

Used to describe Tray 1/MPT.

IOT

Image Output Terminal

Used instead of printer.

2TM

Two-tray Module

Option Trays 4 and 5 or 1000-Sheet Feeder

P/J

Plug/Jack

Plug (P) and or Jack (J) designators

EM

Exit Module

Used for either Exit (1 or optional Exit 2).

SW

Switch

Appears as a designator.

NVM

Non-volatile Memory

Used instead of NVRAM.

CRUM

Customer-Replaceable 
Unit Monitor

Device used to store usage information on the 
Drum and Toner Cartridges.

Comm

Communication

As in MCU-DM Comm Error.

LVPS

Low-Voltage Power Supply

Primary power supply.

PWB

Printed Wire Board

Used to describe a circuit board (Tray 6 PWB).

Summary of Contents for Phaser 5500
















































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands