Fuji Xerox Phaser 5500 Service Manual Download Page 285

Page: 285 / 623

Error Messages, Codes, and Procedures

3-207

Drum Cartridge Near End of Life - DRUM Life Near End

The Drum Cartridge is near its end of life count or the Drum Cartridge CRUM PWB
has failed to communicate with the Engine Logic Board.

Check Toner Dispense Motor connections.
Are P/J216 and P/J420 connected?

Go to Step 7.

Connect P/J216
and P/J420.

Check continuity between the Toner
Dispense Motor and Engine Logic Board.
Is there continuity on each wire
between P/J216 <=> P/J420?

Go to Step 8.

Repair the wiring.

Check for +24 V to Toner Dispense Motor
Is there +24 V across P/J420-2 (+) <=>
ground?

Replace the Toner
Dispense Motor
(page 8-73).

Replace Engine
Logic Board
(page 8-89).

Drum End of Life (Drum CRUM) Troubleshooting Reference

Applicable Parts

References

■

Drum Cartridge

■

Drum Cartridge
CRUM PWB

■

Engine Logic Board

■

Print Engine P/J Drum and Toner (page 10-6)

■

Print Engine P/J Engine Logic Board (page 10-13)

■

Print Engine Drive/CRUM Wiring (page 10-25)

■

PL5.1 Laser, CRU and Toner Dispense (page 9-32)

■

PL8.1 Print Engine Electrical (page 9-40)

Drum End of Life (Drum CRUM) Troubleshooting Procedure

Step

Actions and Questions

Yes

Check the Drum Cartridge installation.
Was the Drum Cartridge replaced?

Go to Step 2.

Replace the
Drum Cartridge. If
the error persists,
go to Step 2.

Check the Drum Cartridge CRUM PWB
installation.
Is the Drum Cartridge CRUM PWB
installed correctly?

Go to Step 3.

Correct the
installation.

Check the Drum Cartridge CRUM PWB
connection.
Are P126 and P/J419 connected?

Go to Step 4.

Connect P126
and P/J419.

Low Toner Troubleshooting Procedure (Continued)

Step

Actions and Questions

Yes

Summary of Contents for Phaser 5500
















































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Phaser 5500

Reviews:

Brands by name

Popular brands

Fuji Xerox Phaser 5500, Service Manual

Search results

Summary of Contents for Phaser 5500

Reviews:

Brands by name

Popular brands