manualshive.com logo in svg

Fuji Xerox Phaser 5500, Service Manual

Share
Download
Fuji Xerox Phaser 5500 Service Manual Download Page 259

Error Messages, Codes, and Procedures

3-181

Stacker Lower Tray Failure - H5-86 Side Regi SNR OFF

Either or both Side Registration Sensors do not transition within the time interval 
specified (500 ms) following activation of the Punch Move Motor or the state changes 
to On after the Punch Move Motor stops.

Applicable Error Code

Stacker Lower Tray Failure - H5-86 Side Regi SNR OFF

18

Check Set Clamp Clutch Harness 
continuity.

1. Disconnect P/J8338B and P/J8304.

2. Check for continuity at the following:

J8338B-1 <=> P/J8304-20
J8338B-2 <=> P/J8304-22

Are these conductive?

Go to Step 19.

Repair the Set 
Clamp Clutch 
Harness.

19

Check for +24 V to the Set Clamp Clutch.
Is there +24 V across J8304-22 <=> 
ground on the Finisher Main PWB?

Go to Step 20.

Replace the 
Finisher Main 
PWB 
(page 3-248).

20

Replace the Set Clamp Clutch.
Print a Test Print.
Does the error still occur?

Replace the 
Finisher Main 
PWB 
(page 3-248).

Problem solved.

Punch Failure (Side Registration Sensors) Troubleshooting Reference

Applicable Parts

References

■

Punch Move Motor

■

Punch Drive Harness

■

Finisher Main PWB

■

Engine Logic Board

■

Side Registration 
Sensors

■

Punch Sensor 
Harness

■

Punch Unit Harness

■

Phaser 5500 Printer Options Service Manual

■

Finisher Main PWB P/J Locator (page 5-35)

■

Finisher Punch P/J Locator (page 5-31)

■

Finisher Punch (1/2) Wiring (page 5-46)

■

Finisher Punch (2/2) Wiring (page 5-47)

■

PL8.1 Print Engine Electrical (page 9-40)

■

PL25.7 Finisher Punch (page 4-56)

■

PL25.14 Finisher Electrical (page 4-70)

■

PL25.15 Finisher Harness (page 4-72)

Eject Clamp (Set Clamp Home Sensor) Troubleshooting Procedure (Continued)

Step

Actions and Questions

Yes

No

Summary of Contents for Phaser 5500
















































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands